Model WKP5LM can hold up to 5 PIN Numbers. Model WKP250LM can hold up to 250 PIN Numbers. Assembly Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Keypad will beep. Keypad will continuously beep indicating no Master PIN Number has been programmed. Proceed to Initial Setup. Keypad Initial Setup Step 1: On keypad press: Step 2: Enter 4 digit Master PIN Number. Example: 1234. ?? Multiple Keypads at Same Location Step 1: On secondary Keypad en

The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? 2 Mount Keypad Step 1 Choose mounting location for Keypad. Remove the back panel and attach it to a solid surface or post. Mount the Keypad onto the back panel with screws. Tighten screws with Allen wrench. Step 2 It is recommended that Keypad be mounted to a Gooseneck post or non-metallic surface. If it is necessary to mount Keypad to a metal surface, use a non-metallic spacer to move the Keypad away fr

Mute: To temporarily mute Base Station, hold the Volume and Talk buttons down for three seconds. The Base Station will reactivate after one hour, or by pressing the Talk button. Remote Button: If there is an accessory device connected to the relay on the PIR Motion Sensor, it can be activated by pressing the Remote button within 30 seconds of the signal from the alert buzzer. On/Off: To turn Base Station OFF hold down the Volume button until a beep is heard and light goes out. To turn Base Stati

1 2 PIR Motion Sensor Assembly & Test Connect PIR Motion Sensor box to mounting plate with silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. A Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) B Ensure batteries do not touch circuit board. Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash after several seconds. Plug in Base Station. Adhere rubber pads to bottom. 4 AA Alkalin

The Safety Sensors are designed to detect an obstacle in the path of the electronic beam and stop the gate operator. CARTON INVENTORY Verify carton inventory below. Hex Head Bolt (2) Wing Nut (2) IMPORTANT INFORMATION ABOUT THE SAFETY SENSORS When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. The sensors must be installed so that the sending and receiving eyes face each other across the gate, no more than 24" (61 cm) above the groun

Ademas, para una instalacion correcta debajo de un alero, quite la proteccion adhesiva de la parte posterior del protector de lampara y peguela como se muestra abajo. Solo para montaje electrico: . Gire la cabeza del detector hacia la union del tornillo sujetador. ControlesTornillo Sujetador . Entoncesgirelacabezadeldetectorhacialaderechapor180°hastaqueloscontrolesmirenhaciaabajo. Sieldetectorsesaledelaunionesferica,aflojeeltornillosujetadoryempujeeldetectorhaciadentrodelaunionesferica.Aprieteel

• Ahorros adicionales de energia con las bombillas fluorescentes compactas. Este paquete tiene: Portalamparas Enchufe de caucho Colgador plastico Control de luz 2 conectores de alambre (3 dimensiones) 1 perno Lamina de montaje Empaque 2 Bombillas 6 tornillos fluorescentes compactas Requisitos • El Control de Luz requiere 120 VCA. • Para usar el Sobrecontrol Manual, conecte el control con un interruptor. • Algunos codigos requieren instalacion por un electricista calificado. • Se recomienda usar

Modelo SH-5412 Caracteristicas • Prende la luz cuando detecta movimiento. • Apaga la luz automaticamente. • La fotocelula mantiene la luz apagada durante el dia. FUNCIONAMIENTO Modalidad: tiempo encendido Trabaja: Dia Noche Prueba 5 seg. x x Autom. 1, 5 o 10 min. x Manual Hasta el amanecer* x *Se pone en Automatico al amanecer. Nota: Cuando lo prenda por primera vez espere 1 1/2 minutos para que el circuito se claibre. Para PRUEBA: 10 5 1 TESTON-TIMEPonga el interruptor de tiempo (ON- TIME), al

Password can be easily changed if desired. Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries. Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes. Operation: Opener activates when 4-digit password and Enter button is pressed. If wrong

¦ The door WILL NOT CLOSE unless The Protector System® and cable tension monitor are connected and properly aligned. ¦ Periodic checks of the operator are required to ensure safe operation. ¦ The model number label is located behind the hinged door of your operator. ¦ Do NOT exceed 10 complete cycles of door operation per hour. 2 YEAR WARRANTY Serial # Installation Date TABLE OF CONTENTS Introduction 2-5 Safety symbol review and signal word review . . . . . . . . . . 2 Planning . . . . . . . . .