Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual. NOTICE:Ifyourinstallationdoes not meet the minimum clearances shown, you must do one of the following: • operate the logs only with the flue damper open • raise the mantel to an acceptable height • remove the mantel FLOOR CLEARANCES A. If installing appliance on the floor level, you must maintain the minimum distance of 14" to combustibles (see Figure 8). B. If combustible materials are less than 14" to the fireplace, you must install appliance at least 5" above the combustible flooring (see Figure 9). Figure 6 - Minimum Mantel Clearances Without Using Hood Minimum Non- Combustible Material Minimum Non- Combustible Material Height Distances to Underside ofMantel Mantel Shelf12" (A) 18"20"22"24" 2 1/2" 6" 8" 10" Underside of Mantel Shelf All minimum distances are in inches Log Set All Models Top of Fireplace Opening Mantel Shelf Minimum Noncombustible Material 8" Min. 12" 15" 18" in inches 20" 2 1/2" 6" 8" 10" 12" Underside of Mantel Hood (GA6050, GA6052 or GA6053) Top of Shelf Figure 7 - Minimum Mantel Clearances When Using Hood Underside of Mantel All minimum distances are Fireplace Opening Figure 8 - Minimum Fireplace Clearances If Installed at Floor Level 14" Min. Combustible Material Noncombustible Material Hearth Combustible Material 5" Min. Figure 9 - Minimum Fireplace Clearances Above Combustible Flooring 113183-01B INSTALLATION Continued INSTALLING HEATER BASE ASSEMBLY CAUTION: Do not pick up heater base assembly by burners. This could damage heater. Only handle base assembly by sides of base. WARNING: You must secure this heater to fireplace floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak. WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting and controls beingdamaged. Raisefireplacefloor with noncombustible material. Make sure material is secure. 2. Locate two masonry screws in hardware package. 3. Place heater base in fireplace. 4. Place logs in their proper position on heater base (see Installing Logs, page 14). 5. Center heater base and logs front-to-back and side-to-side in fireplace. 6. Carefully remove logs without moving heater base. 7. Mark screw locations through one hole on each side of the mounting bracket (see Figure 11). If installing in a brick-bottom fireplace, mark screw locations in mortar joint of bricks. 8. Remove heater base from fireplace. If installing optional control accessories, do so at this time. Follow all directions provided with accessory. 9. Drill holes at marked locations using 3/16" drill bit. 10. Attach base assembly to fireplace floor using two masonry screws (in hardware package). IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly. Avoid damage to thermostat bulb. Avoid nicks or sharp bends in thermostat bulb wire. Keep thermostat bulb in mounting bracket until ready to mount base to floor. See Optional Positioning of Thermostat Sensing Bulb, page 24. Installation Items Needed • hardware package (provided with heater) • approved flexible gas hose and fitting (not provided) (if allowed by local codes) • sealant (resistant to propane/LP gas, not provided) • electric drill with 3/16" drill bit (metal or masonry as applicable) • flathead screwdriver 1. Connect fitting to base as shown in Figure 10. Connect approved flexible gas hose to fitting in base (see Figure 10). IMPORTANT: Hold gas fitting with wrench when connecting flexible gas hose. Figure 10 - Attaching Flexible Gas Hose to Heater Fitting Flexible Gas Hose (if allowed by local codes) Masonry Mounting Flange Screw Figure 11 - Attaching Base Assembly to Fireplace Floor 113183-01B Propane/LP Supply Tank External Regulator Propane/LP Supply Tank External Regulator INSTALLATION Continued CONNECTING TO GAS SUPPLY WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator. WARNING: A qualified servicepersonmustconnectheater to gas supply. Follow all local codes. CAUTION: For propane/LP gas, never connect heater directly to the propane/LP supply. This heater requires an external regulator (not supplied). Install theexternalregulatorbetweenthe heater and propane/LP supply. Installation Items Needed Before installing heater, make sure you have the items listed below. • external regulator for propane/LP only (supplied by installer) • piping (check local codes) • sealant (resistant to propane/LP gas) • equipment shutoff valve * • test gauge connection * • sediment trap • tee joint • pipe wrench * A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable ...