Fabricar: GE
Tamaño del archivo: 1.09 mb
Nombre del archivo:
|
Resumen del manual
Hot exhaust and vent may cause serious burns. Keep back from water heater unit. Keep small children and animals away from unit. CAUTION: Hot Water outlet pipes leaving unit can be hot to touch. Insulation must be used for hot water pipes below 36" due to burn risk to children. NOTE: It is recommended to install the bottom of the unit at least 18" off the ground to minimize blockage and maintenance from debris and provide room for the optional Pipe Cover Accessory Model Number AGTPCM. NOTE: Do not install electrical outlet directly below unit. Electrical outlet must be installed less than 6 feet from unit. 9 Installation Instructions CLEARANCES FOR WATER HEATER A WARNING: Combustible construction refers to adjacent walls and ceiling and should not be confused with combustible or flammable products and materials. Combustible and/or flammable products and materials should never be stored in the vicinity of this or any gas appliance. To combustibles To noncombustibles Top of heater 6 inches (152 mm) 2 inches (51 mm) Back of heater 0 (zero) 0 (zero) Front of heater 6 inches (152 mm) 6 inches (152 mm) Sides of heater 2 inches (51 mm) 1/8 inch (3 mm) Floor/ground 12 inches (305 mm) 12 inches (305 mm) Vent 0 (zero) 0 (zero) Closet 6 inches (152 mm) from front 6 inches (152 mm) from front *Every vent connection must be accessible for inspection, cleaning and replacement. CORROSIVE ATMOSPHERES NOTICE: The water heater or intake air supply should not be installed near an air supply containing halogenated hydrocarbons or near swimming pool chemicals. MOUNTING THE WATER HEATER A CAUTION : Reinforcement of the wall is required in case the wall is not strong enough to hold the water heater. Do not mount to drywall unless mounting screws are secured in wall studs. Make sure the location of the water heater allows for easy access and operation. Wall studs should be utilized when mounting the water heater to the wall. On masonry or concrete wall, use concrete anchors or lag bolts. m Identify the installation location and confirm that the installation will meet all required clearances. Use mounting template to locate screw and anchor locations. [U Securely attach the water heater to the wall using the brackets located at the top and bottom of the water heater. [U Ensure that the attachment strength is sufficient to support the weight. Refer to the weight of the water heater in the Specification Guidelines. Four mounting screws with 200 lb. tensile load capability are required at a minimum. r\ o In«, O u ObiI'1 — Wall installation brackets 10 Installation Instructions MOUNTING THE WATER HEATER (cont.) 1X1 FINISHED WALLS (Drywall) Option 1: Mount boards over drywall directly to studs in the wall. When attaching the unit to a finished wall, mount two boards suitable for anchoring to wall studs. Level the unit during installation. NOTE: Do not hang the unit on drywall only. The unit must be secured into wood mounting board. Boards on outside of finished wall FINISHED WALLS (Drywall) Option 2: Framed wall with boards behind the drywall. Mount the unit to boards in the wall. Do not use the screws provided to mount through drywall. Screws long enough to penetrate the drywall and provide at least 1" of engagement in wood should be used. Screws should be rated to carry a tensile load of 200 lbs each. Level the unit during installation. Boards on inside of finished wall NOTES: • Screws provided must fasten securely and directly into wood. If screws go through drywall and do not fully engage the wood stud, the installer must supply correct screws. • Do not hang the unit on drywall only. The unit must be secured into wood mounting board. 11 MOUNTING THE WATER HEATER (cont.) ON MASONRY OR CEMENT WALL: Mount 4 wall anchors (not supplied) in a wall suitable to carry 200 lbs minimum tensile load each. Level the unit during installation. IMPORTANT: Anchors suitable for masonry or concrete are to be supplied by the installer. Installation Instructions CONNECTING THE WATER HEATER TO GAS AND WATER [T| GAS PIPING GENERAL INSTRUCTIONS • Make sure gas supply is off prior to making any connections to the water heater. A manual gas control valve, provided with this water heater, must be placed in the gas supply line to the water heater. A union can be used on the connection above the shut-off valve for the future servicing or disconnection of the unit. • Check the type of gas and the gas inlet pressure before connecting the water heater. If the water heater is not of the gas type that the building is supplied with, DO NOT connect the water heater. Contact the dealer for the proper unit to match the gas type. • Check the gas supply pressure immediately upstream at a location provided by the gas company. Supplied gas pressure must be within the limits shown in the Specifications section. • Before placing the appliance in operation, all joints, including the heater, must be checked for gas tigh...
Otros modelos de este manual:Calentadores de Agua - GN75DNSRSA (1.09 mb)
Calentadores de Agua - GP94DNSRSA (1.09 mb)