Iniciar sesión:
Votos - 2, Puntuación media: 4 ( )

Manual de usuario Haier, modelo S110ENL

Fabricar: Haier
Tamaño del archivo: 189.25 kb
Nombre del archivo: 47827217-2843-49ad-8339-2c0ed12b84fc.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


If there is a shading object, the distance between it and the water heater should be longer than L. L=H/tg(66.5 -a) (where H: height of the shading object; a: local latitude) Note: Installation of the water heater must be conducted by professional personnel. 4 Installation instructions .. Outline and installation dimensions of the water heater Outline dimensions (in mm) Installation dimensions (in mm) Model A H D B S75ENF 1166 1457 1000 1351 S85ENF 1306 1457 1140 1351 S110ENF 1296 1710 1140 1590 S125ENF 1456 1710 1300 1590 S150ENF 1696 1710 1540 1418 S75ENL 1166 1457 1000 1351 S85ENL 1306 1457 1140 1351 S110ENL 1296 1710 1140 1590 S125ENL 1456 1710 1300 1590 S150ENL 1696 1710 1540 1418 Note: error of above dimensions: ..% Installation instructions • Assembling the bracket See the attached paper in the bracket packing case for assembly drawing and packing list of the bracket. • Securing the bracket 1. Recommend you to secure the legs of the water heater on a foundation with embedded irons. You can also make cement bricks, attach expansion bolts in the cements and fix the heater legs on the expansion bolts. 2. Adjust the height of the bracket using the hard, waterproof spacers to ensure levelness of the water tank as well as even the load of each leg. Notes: 1. Ensure close contact of all legs of the water heater with the support plane. No legs are allowed to hang in the air as this may cause deformation of the bracket and thus damage the water heater. 2. In the areas where typhoon happens frequently, fix the water tank and bracket firmly on the roof with wire rope. 3. The water heater must be installed stably and firmly. Otherwise serious damage or injury may occur in bad weather. • Installing the water tank 1. Take the water tank from the packing case and remove the nuts and shims attached to the bolts on both sides of the tank. 2. Insert the bolts on the bottom of the tank into the long holes in the tank support of the bracket and attach the shims and nuts. Notes: 1. To reduce scratching, remove the protective plastic film from the water tank after the installation is finished. Never use sharp tools such as wallpaper knives to remove the film. 2. The assembly of the water tank is realized by bolt connection and nut fixing. Tighten all nuts after the assembly of whole water heater is finished. 3. When installing the water tank, please keep the center lines of the connection holes of the vacuum tubes parallel with the oblique-pulling posts of the bracket. Installation instructions • Installing the vacuum tubes 1. Before installing, the vacuum tubes should be protected from sunshine. Otherwise you may be burned during installation. 2. Put the wind shroud on a vacuum tube (Fig. A). 3. Insert the vacuum tube with even force while rotating to turn it into the seal rings. The direction of the resultant force should be consistent with the axis of the vacuum tube. 4. Put the tail-holder into the tailstock (Fig. B) and then fasten the vacuum tube on the t...

Otros modelos de este manual:
Calentadores de Agua - S110ENF (189.25 kb)
Calentadores de Agua - S85ENL (189.25 kb)
Calentadores de Agua - S125ENF (189.25 kb)
Calentadores de Agua - S125ENL (189.25 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría