Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Fig. 1 Fully Closed Fig. 2 Fully Open Note: Opening or part opening of the ash door is controlled by the "interlock" device located in the front of the unit (refer to INTERLOCK section on page 9). Even when all the slots are completely shut a "bleed" of secondary air will be maintained ensuring that inflammable gases are burnt off. DISASSEMBLE AIR WASH The Stratford air wash may be disassembled for cleaning or adjustment. To achieve this, the following procedure should be followed: This should only be carried out when the fire is cold and unlit. •Support Air wash cover with one hand •Move cover up by smartly tapping the bottom with a hammer. (Fig. 3) •Remove assembly from appliance. •Clean and/or adjust. •Refit using reverse procedure. Fig. 3 Stratford Tf & Ti Multifuel Boiler Stoves OPERATING INSTRUCTIONS INTERLOCK SYSTEM Stratford Tf and Ti Multifuel Boiler Stoves are fitted with an "interlock" system. A situation where the fire door is closed and the ash door is open may lead to serious overfiring which could damage the appliance. Correct use of the doors and interlock system will ensure that this does not happen. Operation is as follows: A pivoted lug prevents closure of the fire door, unless the ash door has been shut first. When the fire door is shut the ash door knob can be turned anti-clockwise by up to 95 degrees creating a variable gap between the top of the ash door and the body, through which primary combustion air can enter the appliance. Note: In order to turn the ash door knob sufficiently for the catch to release and permit the ash door to be opened fully THE FIRE DOOR MUST BE OPENED FIRST. MULTI PURPOSE OPERATING TOOL Your Aarrow fire comes with a multi-purpose operating tool which is used to open the ashpit door, riddling, setting the multifuel grate position and for emptying the ash pan. (see fig.4) Fig. 4 RIDDLING Use the operating tool for setting the grate in the coal burning position or the wood burning position. This means that effective de-ashing takes place, and also allows the grate to be set in the coal burning or wood burning position, as indicated on the right hand side of the appliance. DOOR TRIM Stratford fire doors are fitted with a brushed steel finish trim as standard. This clips on to the small lugs at the top and bottom of the aperture in the cast iron fire door, as a "spring fit". When fitted, the trim locks the glass retaining clips in position. (Fig 5) The fire door should be removed so that the above operations can be carried out on a workbench or similar. Remove the door by GENTLY tapping the door upwards; this will lift off of its hinges. Trim Fit Fig 5 FIRE DOOR GLASS If necessary the glass can be removed as follows Step 1 Remove the brushed steel finish trim by pressing on the curved edge at the top until the trim can be disengaged from the lugs. Step 2 Slide the two glass retainer clips on one side only, inwards, towards the centre of the door as far as they will go. Step 3 Pull this side of the glass away from the door casting, easing the tags on the glass retaining clips past the edge of the aperture in the door casting. Stratford Tf & Ti Multifuel Boiler Stoves OPERATING INSTRUCTIONS Step 4 Remove the glass completely. Store glass- retaining clips and white gasket (if sound) safely for re-use. Step 5 Follow this procedure in reverse to fit replacement door glass or gasket. GLASS GL ASS CLIP GASK ET FIRE DOOR Fig. 6 DOOR ADJUSTMENT The catch can be adjusted by sharply tapping the catch on the inside of the door. Once the appliance has been under fire for a period of time the fire door may appear to have moved out of alignment with relation to the door aperture or catch on the door interlock mechanism. This is quite normal and due to the settling of the casing. The fire door can be re-aligned by the user as follows: •When the appliance is cold, open the fire door so that it is at a right angle to the front face of the fire. •Lift the fire door up off the hinges. •Gently tap the two hinge pins in a direction to compensate for the misalignment.(fig 7) Fig. 7 •Refit the door and check to ensure it now sits square to the body; if not repeat above steps. Raising the door as follows: •When the appliance is cold, open the fire door so that it is at a right angle to the front. •Lift the fire door up off the hinges. •Drop one washer on the top and bottom hinge pin. •Refit the door and check to ensure door is free of the interlock. If not remove and repeat fitting second washer. FUEL RETAINER BARS Fuel retainer bars are supplied with the fires. For wood burning, 1 fuel retainer bar is used, affording a better view of the fire. Slide and lift the bar until it is clear of the guides at each side, and remove through the fire door opening. The bars are symmetrical and of even lengths making incorrect fitting impossible. Note: This operation should only be carried out when the appliance is unlit and cold. Stratford Tf & Ti Multifuel Boiler Stoves OPERATING INSTRUCTIONS FUEL T...
Otros modelos de este manual:Calentadores de Agua - Stratford Tf (1.33 mb)