Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
If the storage tankis full of salt, it is hard to tell if you have a salt bridge. Salt is loose on top, but the bridge is under it. The following is the best way to check for a salt bridge. Salt should be loose all the way to the bottom of the tank. Hold a broom handle, or like tool, up to the softener as shown in FIG. 10. Make a pencil mark on the handle, 1" or 2" below the top height of the rim. Then, carefully push it straight down into the salt. If a hard object is felt before the pencil mark gets to the top of the tank, it's most likely a salt bridge. Carefully push into the bridge in a few places to break it. Do not try to break the salt bridge by pounding on the outside of the salt tank. You may damage the tank. If the wrong kind of salt made the bridge, take it out. Then fill the tank with nugget or pellet salt only. softener use all the salt before adding. Without salt, you will soon have hard water. Note: You will have a loss in softening capacity and may get partly hard water if less than 10 inches of salt is in the storage tank. FOR DIRECTIONS ON ADDING SALT. BRIDGE Salt Bridge pushtoolinto salt bridge to break 1 n _ 2 n pencil m&rR salt salt broom brid,ge handle water level 3-1 Problems, Questions? Call 1-800-426-9345 Kenmore Water Line SECTION 3 CARE OF YOUR WATER SOFTENER B. KEEPING THE WATER SOFTENER CLEAN NOZZLE & VENTURI Cleaning Nozzle & Venturi A clean nozzle and venturi (FIG. 11) is a must for the Gap softener to work right. This small unit moves brine from the salt storage tank to the resin tank during re generation. If it becomes plugged with sand, silt, dirt, etc., the softener will not work and you will get hard water. "lb get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no water pressure at nozzle and venturi). 1) Turn off the cap from the nozzle and venturi housing. 2) Lift out the screen support and screen, do not lose the large o-ring seal. 3) Then the nozzle and venturi. Wash and rinse the parts in warm water until clean. If needed, use a (HVDO) small brush to remove iron or dirt. Also check and Nozzle & Venturi clean the gasket, flow plugs and screens. Housing Carefully replace all parts in the correct order. Lubricate the o-ring seal with silicone grease or Vaseline and place in position. Install and tighten the cap, by hand only. Do not overtighten and break the cap or housing. IRON FROM RESIN BED ter or other equipment is needed. Your local Sears store has trained people to help you with iron water Your water softener takes hardness minerals (cal problems. cium and magnesium) out of the water. Also, it can control some "clear water" iron. See maximum al lowed in the specifications on page 4-1. With clear If your water supply has clear water iron, even water iron, water from a faucet is clear when first though less than the maximum allowed, regular put into a glass. After 15 to 30 minutes, the water be-resin bed cleaning is needed. Your local Sears store gins to cloud or turn rust colored. A water softener has resin bed cleaner, Item No. 42-34426 for this. WILL NOT remove any iron which makes the water Clean the bed at least every 6 months. If iron shows cloudy or rusty as it comes from the faucet (called up in the soft water before 6 months, clean more red water iron). "lb take red water iron out of water, often. Printed instructions are on the resin bed or over the maximum of clear water iron, an iron ill-cleaner bottle. 3-2 Problems, Questions? Call 1-800-426-9345 Kenmore Water Line SECTION 3 CARE OF YOUR WATER SOFTENER C. PROTECT THE WATER SOFTENER FROM FREEZING If the softener is installed where it could freeze Drain All Water From Softener (summer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. _lb drain the softener: i i i []Close the shut-off valve on the house main wa ter pipe, near the water meter or pressure tank. []Open a faucet in the soft water pipes to vent pressure in the softener. i, []Refer to FIG. 14 on page 4-1. Move the stem in a single bypass valve to bypass. Close the inlet and outlet valve in a 3-valve bypass system, and I open the bypass valve. If you want water in the house pipes again, reopen the shut-off valve on drain wood block the main water pipe. []Unplug the transformer at the wall outlet. Re-_ Looking at FIG. 12, lay a piece of 2 inch thick move the salt hole cover and the main cover, board near the floor drain. Move the softener _lhke off both drain hoses, close to the drain. SLOWLY and CAREFULLY, tip it over until the rim rests on the wood block []Carefully remove the large holding clips at the with the inlet and outlet over the drain. Do not softener inlet and outlet (see Key No. 66, on page allow the softener's weight to rest on the inlet 6-3). Separate the softener from the copper and outlet fittings or they will break. tubes, or from the bypass valve. [] Tip the bottom of the softener up a few inches and hold until all water has drained. Le...