Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
¦ After installation Use after throwing away the water in the water tank up to full level more than twice. Hot water caution ¦ Take care to avoid burns when extracting hot water. ¦ Draining hot water Pull the drainage door at the side downwards, and insert the drainage hose; this way, you can completely drain the hot water inside the system. . Note: take care not to burn yourself, since hot water suddenly starts to drain as soon as the hose is inserted. ¦ How to Use Please Keep In Mind Preparations / 18 19 PREPARATIONS OPERATION PART /INDICATION PART . Please check before use Regular filter change The regular filter change is very important to have clean water. The filter after life is ended may degrade the performance. Thus, do not miss the time for the filter change. ¦ In case of no service for a long time In case of no service for a long time, completely drain the water from the tank. Next, fill and empty water again. And use the product. ¦ When not using for a long time please lock the main water supply valve and plug out the power cord. . Operation Part/Indication Part Hot water lock button Hot water mode lamp / hot water 3 step LED 1 Cold water mode lamp / cold water 3 step LED 2 3 . Hot water lock on 4 Light detection sensor 8 Hot water button 5 . . Cold water button . 7 . . . Room water button 6 . The lamp is on when hot water mode is selected. The lamps reflect the temperature of the water, so more lamps come on as the temperature gets higher. Hot water mode lamp Hot water temperature 3 step LED The lamp is on when a cold water mode is selected. The lamps reflect the temperature of the water, so more lamps come on as the temperature gets lower. Cold water mode lamp Cold water temperature 3 step LED 1 2 When the hot water lock button is pressed for three seconds, hot water cannot be extracted, even by pressing the hot water button, and an alarm goes off. Hot water lock button The lamp goes on when the hot water lock button is selected. 3 4 Hot water lock on How to Use Preparations Operation Part/Indication Part / 20 21 OPERATION PART /INDICATION PART . Operation Part/Indication Part When using cold water Press the cold button, and check if the cold water mode lamp is on. ¦ Press the cold button, check if the cold water mode lamp is on, and extract water. Cold water button Detects the ambient light, reducing energy usage by automatically decreasing the operation frequency of the cooler. 7 8 Light detection sensor To use hot water, press the hot button, check if the hot water mode lamp goes on, and extract water. (However, the mode automatically returns to cold water mode three seconds after hot water has been extracted.) Hot water button To use room water, press the room button and extract water. 5 6 Room water button When using room water Press the room button, and touch the extraction part. ¦ When using the hot water lock Press the hot water lock for three seconds. Check if the hot water lock lamp comes on. ¦ Light detection sensor setting function Press the hot and cold buttons together for three seconds; the hot water mode lamp flickers as shown in the picture with a “pinging” sound, and the system enters the setting mode. Press the cold button once; the cold water mode lamp comes on, and the light detection sensor function is set. (When the cold water mode lamp goes out, the function is disabled.) After setting the mode, press the room button for three seconds; the system saves the last set mode and converts to standby mode. ¦ To use hot water Press the hot button, and check if the hot water mode lamp is on. ¦ To use both the hot water and cold water modes, press each button for more than three seconds. Once both hot water and cold water mode lamp go on, you can use them. “Light detection sensor” is set to disabled status at the initial usage Fixed quantity extraction function Press the hot and cold buttons together for three seconds; the hot water mode lamp flickers as shown in the picture with a “pinging” sound, and the system enters the setting mode. The quantity is adjusted each time the hot button is pressed (120cc ..200cc ..300cc .. 120cc), and the hot water mode lamp goes on according to each quantity phase. After completing the mode setting, press the room button for more than three seconds; the system saves the last set mode and converts to standby mode. ¦ set unset 120cc 200cc 300cc . . How to Use Operation Part/Indication Part 22 23 HOW TO OPERATE . To drink cold water Press the cold button after the cold water mode lamp has come on, and touch the extraction part. .. . To drink hot water Presse the hot button after the hot water mode lamp has come on, and touch the extraction part. . To drink room water Press the room button and touch the extraction part. .. . Continuous extraction 3seconds Select the water mode you desire, and touch and hold the extraction part for 3 seconds or more. The extraction part LED flickers, signifying continuous extraction, and discharges water for 60 secon...