Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Hilex, Clerox, etc.) and mix in the water. DO NOT ADD CHLORINE FIRST. Concentrated, it will attack plastics, 6. Replace the cap, with o-ring, and install the retaining clamps. 7. Connect the RO faucet product water tubing directly to the tank shutoff valve, isolatinq the carbon postfilter. 8. Open the tank shutoff valve, and the water supply to the RO. Open the RO faucet, locking the lever upward, against the spout. 9. Allow water to circulate through the system until the bleach odor is gone. 10. Turn off the water supply to the RO. Close the RO faucet after water flow stops. 11. Reconnect the postfilter (replace used filter) to the RO system, Fig. 9, page 13. 12a. Do steps 2 and 3. b. Replace the RO cartridge and prefilter cartridge (BE SURE YOUR HANDS ARE CLEAN). c. Do step 6. d. Turn to page 10 and do the pressure testing and purging steps B through E. 15 -CARE OF YOUR HOME DRINKING WATER SYSTEM RO CARE GUIDE MODEL RO 2000 WITH MONITOR IMPORTANT: BEFORE DOING THE FOLLOWING MAINTENANCE, BE SURETO RELIEVE PRESSURE AND ALLOW AIR TO ENTER THE TANK, STEPS 1, 2 AND 3, PAGE 12. t. Replace the prefilter cartridge and postfilter when the amber "FILT" light begins to flash while taking product water from the RO faucet. Clean or replace the flow control and screen. and replace the batteries in the electronic control box. 2. Replace the RO membrane cartridge when the amber"RO" light begins to flash while taking product water from the RO faucet. Clean or replace the flow control and screen. NOTES: a. If slow making of product water occurs before an amber light begins to flash, replace the prefilter cartridge. If production rate does not improve, then replace the postfilter and RO membrane, b. If product water flow from the RO faucet is slow, do the steps referred to in the IMPORTANT note above. OTHER TROUBLESHOOTING PROBLEM CAUSE CORRECTION Chorine taste and/or odor the RO product water in The ppm of chlorine in your water supply exceeds maximum limits, and has de- Ifthewater supplycontains morethan 2.0 ppmof chlorine, additional filtering of the water supply to the RO is needed. Correcl stroyed the RO membrane. this condition before doing maintenance on the RO system. The prefilter is no longer removing rine from the water supply. chlo-Replace the RO membrane cartridge, flow control, screen, prefilter, postfilter, and batteries in the electronic box. Other taste and/or odor Postfilter expended. Replace the postfilter. Iftaste and odor persists, replace the pre- RO membrane cartridge expended. filter, RO membrane ies in the electronic cartridge, flow control, screen, and batter- box. ! Contamination in product water storage. Use sanitizing procedures. Then replace the postfilter. High total dissolved solids Water supplytothe RO system not within Increasewaterpressure, preconditionthewater, etc.,aeneeded (TDS) in product water specifications. to conform before doing maintenance on the RO system. RO membrane cartridge expended. Replace the RO membrane cartridge, flow control, screen, prefilter, postfilter, and batteries in the electronic box. Slow product water flow from Vacuumcreated in storageareeforprod-Open the vacuum relief valve and allow the tank to fill with air. the RO faucet uct water. See page 12. Waterleaking from faucet air-Drain side of faucet airgap (3/8" tubing) Inspect and eliminate restriction or plug. Refer to installation gap hole plugged, restricted, or incorrectly con-instructions for proper drain connection, nected to drain point. Indicator lights, on faucet Faucet base leadwire not connected to ! base, not working electronic box leadwire. Battery pack not connected to electronicbox. Connect Batteries installed incorrectly, or ex-Observeorientationmarkingsontheholderandinstallcorrectly. _ended. Replace batteries if old. Leadwires or connectors damaged. Inspect and repair or replace as needed. Tubing Connection at Drain Adapter: Cut the end of the tubing square and push into the fitting as far as I possible (11/16"), Pull on the tubing to be sure it is held firmly in place. I To Disconnect Tubing: Push the tubing inward to de-tubing I press the fitting collet. Hold the collet in while pulling the tubing out. collet 16 -DIMENSIONS / SPECIFICATIONS •=--8_ 1/8,,--.-_ 21" METRIC Supply water pressure limits ...................................... 40-125 PSI 280-860 kPa Supply water temperature limits ..................................... 40-100OF 5-40oc Maximum total dissolved solids (TDS) ............................... 2000 PPM Maximum water hardness @ 6.9 pH .................................. 10 GPG Maximum iron, manganese, hyd. sulfide .................................... 0 Chlorine in supply water (SEE PAGE 4) ......................................... Max. 2.0 PPM 1 Supply water pH limits ................... •.......................... 4-10 pH Product (quality) water, 24 hrs.* ..................................... 11 gals. 41.6 liters Waste water per gal. product water, 24 hrs.* .....................
Otros modelos de este manual:Depuradores de agua - WaterWorks RO 2000 (752.88 kb)
Depuradores de agua - WaterWorks RO 2000 (752.88 kb)
Depuradores de agua - WaterWorks RO 2000 (752.88 kb)