Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
To take red water iron out of water, or overthe maximum of clear water iron, an iron filter or other equipment is needed. Your local Sears store has trained people to help you with ironwater problems. If your water supply has clear water iron, eventhough less than the maximum allowed, regularresin bed cleaning is needed. Sears has resin bedcleaner, Stock No. 42-34426 for this. Clean thebed at least every 6 months. If iron shows up inthe soft water before 6 months, clean more often. Printed instructions are on the resin bed cleaner bottle. 16 SECTION 3 CARE OF YOUR SOFTENER 3C. KEEP THE SOFTENER FROM FREEZING If the softener is installed where it could freeze (summer cabin, lake home, etc.), you must drainall water from it to stop possible freeze damage. To drain the softener — 1. Close the shut-off valve on the house main water pipe, near the water meter or pressuretank. 2. Open a faucet in the soft water pipes to ventpressure in the softener. 3. Refer to FIG. 12 on page 19. Move the stem ina single bypass valve to bypass. Close theinlet and outlet valve in a 3-valve bypasssystem, and open the bypass valve. If youwant water in the house pipes again, reopenthe shut-off valve on the main water pipe. 4. Unplug the transformer at the wall outlet. Remove the salt hole cover and the main cover. Take off both drain hoses. 5. Carefully remove the large holding clips atthe softener inlet and outlet (see Key No. 61, on page 30). Separate the softener from theadaptors or bypass valve. 6. Remove the brinewell cover and disconnect the brine valve tubing at the nozzle andventuri assembly (see page 30). Lift the brinevalve out of the brinewell. Tip the brine valveupside down to drain out water. FIG. 11 DRAIN WATER FROM THE SOFTENER 7. Looking at FIG. 11, lay a piece of 2 inch thickboard near the floor drain. Move the softener close to the drain. SLOWLY and CAREFULLY tip it over until the rim rests on the woodblock with the inlet and outlet over the drain. Do not allow the softener’s weight to rest onthe inlet and outlet fittings or they willbreak. 8. Tip the bottom of the softener up a few inchesand hold until all water has drained. Leave the softener laying like this until you areready to use it. Plug the inlet and outlet withrags to keep dirt, bugs, etc. out. 17 SECTION 3 CARE OF YOUR SOFTENER 3D. HELPFUL HINTS CHECKLIST ... TO HELP YOU SAVE MONEY If your water softener fails to work, make the following easy checks. Often, you will find what’s wrong yourself and you won’t have to call and wait for service. If, after making the checks, your softener stilldoes not work right, call your Sears Service Department. NOTE: 1. Also read ERROR CODE, page 11. 2. If an error code is not dispIayed, press and hold the#1SELECTbuttonuntil(example:000--)showsin the display. Then, press the #1 SELECT again and hold until a flashing AR code appears. It must show AR31. If AR 17, 22, 39 or 60 shows, the face plate computer is working on incorrect input andwould probably be the cause of the problem. To set AR31, press either the UP or DOWN button. When AR31 shows, press the #1 SELECT to return a flashing 12:00 AM display. Reset the present time, hardness number and recharge time, pages 6 and 7. PROBLEM CAUSE CORRECTION NO SOFT WATER No salt (or salt bridged) in the storage tank Refill with salt, or break the salt bridge (page 15). Press ON/OFF-HOLD(RECHARGE NOW) button and hold for 3 seconds to start a regeneration (see page 10). Transfomer unplugged at the wall outlet, or Check for loss of power due to any ofpower cable leads loose, fuse blown, circuit these and correct. With the power back breaker popped, or circuit switched off. on, look at the time display and readPROGRAM MEMORY, page 11. Manual bypass valve(s) in bypass position Look at FIG. 12 on page 19. Move the stem in a single valve to service. In a 3-valve bypass, open the inlet and outlet valves, and be sure to fully close the bypass valve. Dirty, plugged or damaged nozzle & venturi Take apart and clean or replace damaged parts (see page 16). Valve drain hose plugged The drain hose must not have kinks, sharp bends, or be raised too high above the softener (see page 16 in your installation manual). WATER HARD SOMETIMES Hardness number setting too low Press and release the SELECT button until HARDNESS shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown on your water analysis report. See page 7 to reset. Press and release the SELECT button until the present time shows in the display. Using hot water when softener is regenerating Avoid using hot water during this time because the water heater refills with hard water (see Automatic Bypass, page 14). Increase in the grains of hardness in your water supply Ask your Sears retail or catalog store for a new water analysis. Then make a new hardness number setting (page 7). 18 SECTION 4 OTHER THINGS TO KNOW 4A. DIMENSIONS/SPECIFICATIONS FIG. 12 BYPASS VALVES INCHES CM A Salt Ta...
Otros modelos de este manual:Depuradores de agua - 625.3485400 (489.6 kb)