Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
WARNING: IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Fig. A Fig. B 4 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Ampere Rating Volts Total Length of Cord in Feet Gauge of Extension Cord 0-6 115 up to 25 18 AWG 0-6 115 25-50 16 AWG 0-6 115 50-100 16 AWG 0-6 115 100-150 14 AWG 6-10 115 up to 25 18 AWG 6-10 115 25-50 16 AWG 6-10 115 50-100 14 AWG 6-10 115 100-150 12 AWG 10-12 115 up to 25 16 AWG 10-12 115 25-50 16 AWG 10-12 115 50-100 14 AWG 10-12 115 100-150 12 AWG 12-16 12-16 12-16 115 115 115 up to 25 25-50 14 AWG 12 AWG GREATER THAN 50 FEET NOT RECOMMENDED Fig. D OPERATING INSTRUCTIONS FOREWORD The Delta ShopMaster Model AP200 Air Cleaner is specifically designed to quietly circulate and filter non-metallic dust which is generated throughout the work area. The Air Cleaner is furnished with two filters: a disposable outer filter which filters out 98% of particles five microns in size; and the secondary filter will capture 85% of dust particles of one micron in size (one micron = one millionth of a meter). Breathing microscopic particles can be a potential health hazard; therefore, filtering out microscopic dust particles of the mentioned sizes will make for a cleaner and safer environment. This Air Cleaner will filter the air in a room measuring 20’ x 20’ x 8’ sixteen times an hour. If desired, multiple units can be used to filter larger areas. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY. 5 AIR CLEANER PARTS 1 2 3 4 Fig. 2 1 -Air cleaner 2 -Four 5/16-18x1." eye-bolts 3 -Four 5/16-18 flange nuts 4 -Four rubber feet 6 ASSEMBLY INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. The Air Cleaner requires very little assembly; therefore, determine in which position the Air Cleaner will be used - on the floor, bench or overhead. If the Air Cleaner will be used as a mobile unit, proceed to “USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE” section. If ceiling mounting, proceed to section “MOUNTING THE AIR CLEANER TO A CEILING OR OVERHEAD SUPPORT.” IMPORTANT: When determining a location to mount the air cleaner, the unit will operate more efficiently when the air flow is unrestricted. Do not locate the unit in a corner or near any heating or cooling vents. USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE 1. Locate (4) self-adhesive rubber feet (D) Fig. 2, supplied with the unit. Carefully place Air Cleaner on a firm supporting surface so there is access to the bottom of the cabinet as shown in Fig. 3. Apply one self- adhesive rubber pad, to bottom at each corner (A) Fig. 3, of air cleaner cabinet. The rubber feet will help eliminate vibration and the possibility of the air cleaner “walking” across the work or floor surface. For operator safety, we suggest that the unit be clamped down when used on a work bench or positioned on sawhorses. A Fig. 3 2. There are two lifting handles located on each side of the cabinet as shown in Fig. 4, to assist in carrying the unit from one place to another. To avoid damage to the air filters, carry the air cleaner with the filters positioned away from your body. CAUTION: THIS MACHINE WEIGHS APPROXIMATELY 50 POUNDS. Fig. 4 7 MOUNTING THE AIR CLEANER TO THE CEILING OR OVERHEAD SUPPORT WARNING: THIS TOOL WEIGHS APPROXIMATELY 50 POUNDS. MAKE CERTAIN THE UNIT IS SECURELY SUPPORTED WHEN MOUNTING TO A CEILING OR OVERHEAD SUPPORT. 1. Remove four screws, one of which is shown at (C) Fig. 5, from the top of air cleaner (D). 2. Thread 5...
Otros modelos de este manual:Aire - AP200 (330.68 kb)