Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Inspect power cord for any damage. Never use fan if any parts are damaged or missing. Never use fan without safety guards attached. 8. When used with an extension cord, use only cord of proper size (Amp rating), UL listed, and with receptacle to accept three prong grounded plug furnished on the fan’s power cord. Always keep power cord and extension cords away from heat, oil, and sharp edges. Inspect cords periodically and replace if damaged. 9. Disconnect fan from power source when not in use, before servicing and when cleaning or repairing. 10. Repair of this appliance should be done by a qualified electrician. 11. In case of power failure, turn fan off at switch to prevent unexpected restarting and component damage. 12. Keep children away from fan at all times. Page 2 Pinnacle Products International, Inc. Portable Air Circulator User’s Manual Portable NEVER LEAVE A FAN OPERATING UNATTENDED Air Circulator Installation Simply locate fan in safe, desired position on level ground, and connect to approved power source. Operation This fan is equipped with a 2-speed control switch. TO START FAN: 1. Be sure the Power Switch is in the middle (OFF) position. 2. Connect to an approved power source. 3. Make sure area is clear from all obstructions. 4. Push Power Switch to the LOW position and allow to operate for 10 seconds. 5. Once 10 seconds have passed, you may now push the Power Switch to the HIGH position. TO TURN OFF FAN: 1 To turn off the fan, simply return Power Switch to the middle (OFF) position. NOTE: For longer parts life, after 10 hours of continuous operation, turn fan off for 15 minutes to allow motor and fan belt to cool. Maintenance and Storage 1. Inspect your fan before each use. Check all wires and extension cords, following the procedure outlined on Page 2 (Safety Information). 2. After use, always be sure fan’s Power Switch is in the OFF position before unplugging. Use cord wrap (see page 4) to keep cord off the ground when transporting fan. Belt Tightening / Replacement 1. Remove screws from Rear Guard and tilt wheel (figure 1). 2. Loosen motor nuts, and motor safeguards (located above and below motor). 3. Remove belt to replace, or adjust motor to tighten belt (figure 2). Belt Replacement (Continued) figure 2 figure 1 Wiring Diagram Pinnacle Products International, Inc. Portable Air Circulator User’s Manual Page 3 Portable NEVER LEAVE A FAN OPERATING UNATTENDED Air Circulator Exploded View 12 34 5 6 7 15 14 20 18 21 1116 12 17 13 10 8 19 9 Replacement Parts Exploded View of Fan Models: Item # Description 36-BDF Series 42-BDF Series 48-BDF Series 1 Front Guard 90-032-0040 90-032-0050 90-032-0500 2 Rear Guard 90-032-0400 90-032-0450 90-032-0550 3 Fan Blade Assembly 90-003-1000 90-003-2000 90-003-5200 4 Motor 90-030-0700 90-030-0800 90-030-0900 5 Leg 90-002-0475 90-002-0475 90-002-0450 6 Pneumatic Wheel 90-008-0300 90-008-0200 90-008-0200 7 Belt 90-037-0400 90-037-0450 90-037-0450 8 Power Switch 90-025-0100 90-025-0100 90-025-0110 9 Pow...
Otros modelos de este manual:Aire - PROTEMP BCB-42-BDF (328.36 kb)
Aire - PROTEMP BCB-48-BDF (328.36 kb)
Aire - PROTEMP PT-42-BDF (328.36 kb)
Aire - PROTEMP PT-48-BDF (328.36 kb)