Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
C. E. D. C.OUTERCASEHOUSINGD.ACCORDE.BASEF.WIRECLEANINGMECHANISMG.REMOVABLECAPG. F. the unit, see Diagram B or F for the loca- tion of the Wire Cleaning Mechanism. Lift and lower the Wire Cleaning Mechanism three to four times to thoroughly clean the internal ionizing wires (see Diagram H in the “CLEANING & MAINTENANCE” section). This movement helps to scrape free particles from the internal ionizing wires. To keep your Ionic Pro® ionic air purifier working properly, it will be necessary to clean the collection blades after every month of use and the internal ionizing wires after every two weeks of use (see “CLEANING & MAINTE- NANCE” and “DEEP CLEANING” section of this manual for the proper techniques). WARNING: After cleaning the collection blades (see “CLEANING AND MAINTENANCE” section) with soap and water, allow at least 24 hours for the collection blades to dry thoroughly before inserting them back into the unit. Water can easily get trapped along the collection blades’ many surfaces and edges and damage could result if there is any moisture on the collection blades. To allow for virtually uninterrupted air purification, a second set of collection blades may be purchased (kept clean and in its box when not in use) and inserted into the Ionic Pro® ionic air purifier while the original collection blades are drying. You will need to clean your Ionic Pro® air purifier more often if it has been exposed to heavy pollution. 5IMPORTANTWARNINGS4IMPORTANTWARNINGS IP_CA500_Mnl_Rev_092707.qxp:Layout 1 6/3/08 2:56 PM Page 8 OPERATING THE IONIC PRO® Getting Ready Locate a level surface on which to place your Ionic Pro® ionic air purifier and a grounded 120v outlet (follow warnings described in the “SAFETY INSTRUCTIONS” section of this manual). Position your Ionic Pro® ionic air purifier at least one foot (12 inches) from the wall. Plug in the unit. You are now ready to turn on your Ionic Pro® ionic air purifier! 7. REMOVABLE CAP 6. WIRE CLEANING MECHANISM INDICATION LIGHT 3. MEDIUM OUTPUT 4. HIGH OUTPUT INDICATION LIGHT 2. LOW OUTPUT 5. CLEAN INDICATION INDICATION LIGHT LIGHT 1. ON/OFF BUTTON Controls/Settings 1. ON/OFF BUTTON Turns unit on and off. 2. LO Recommended for smaller rooms, this is the (low output indication light) most cost-effective setting. At this setting, the unit will experience longer rest intervals than on the other two settings (MED or HI). 3. MED Recommended for average-sized rooms where (medium output indication light) windows and doors are rarely opened. At this setting, the unit will experience shorter rest intervals than when on the LO setting but higher rest intervals than when on the HI setting. 4. HI This maximum output setting is recommended (high output indication light) for large rooms and/or area exposed to heavy dust. 5. CLEAN This red light goes on when your (indication light) Ionic Pro® ionic air purifier needs to be cleaned, or the unit is experiencing some other problem. See the “CLEANING & MAINTENANCE” and “TROUBLE-SHOOTING” sections. 6. WIRE CLEANING MECHANISM This is used to clean the internal ionizing wires. See “CLEANING & MAINTENANCE” for full details. 7. REMOVABLE CAP Lift off the Removable Cap to locate collection blades for cleaning. See the “CLEANING & MAINTENANCE” section. HELPFUL TIPS: In general, LO is the most cost-effective setting and is recommended for smaller rooms. MED is recommended for rarely opened average-sized rooms. HI delivers maximum output and is recommended for larger rooms (the scent of ozone at this setting may be too strong for smaller rooms). 7OPERATINGTHEIONICPRO®IONICAIRPURIFIER6OPERATINGTHEIONICPRO®IONICAIRPURIFIER IP_CA500_Mnl_Rev_092707.qxp:Layout 1 6/3/08 2:56 PM Page 10 CLEANING & MAINTENANCE: Operation Set up the Ionic Pro® ionic air purifier as described in “Getting Ready”. Press the ON/OFF button to activate your ionic air purifier and get ready to enjoy clean, ionized air that cycles through pre-programmed run/rest intervals according to the setting you select. The Ionic Pro® ionic air purifier automatically defaults to the HI (high/maximum output) setting whenever the unit is turned on. Just press the ON/OFF button one more time to select the MED (medium) output setting to enjoy intermittent run/rest periods and press the ON/OFF button once again if you wish to select the LO (low) output setting for the most cost-effective run/rest cycle. Press the ON/OFF button a fourth time to turn the unit off. The indicator LEDs light up to indicate your current setting (LO, MED, HI). Clean Light: The red CLEAN light will turn on and the unit will shut down if cleaning is overdue. The Ionic Pro®ionic air purifier’ s collection blades must be cleaned after every month of use and the internal ionizing wires must be cleaned after every two weeks of use (see “CLEANING & MAINTENANCE” for full directions). Once the collection blades are properly cleaned, thoroughly dried and re-inserted into your Ionic Pro ® ionic air purifier and the internal ionizing w...