Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
INSTALLATION INSTRUCTIONS Assembly and electrical connections must be carried out by specialised personnel. • Electrical Connection The appliance has been manufactured as a class II, therefore no earth cable is necessary. The connection to the mains is carried out as follows: BROWN = L line BLUE = N neutral If not provided, connect a plug for the electrical load indicated on the description label. Where a plug is provided, the cooker hood must be installed in order that the plug is easily accessible. An omnipolar switch with a minimum opening of 3mm between contacts, in line with the electrical load and local standards, must be placed between the appliance and the network in the case of direct connection to the electrical network. • The minimum distance between the support surfaces of the cooking pots on the cooker top and the lowest part of the cooker hood must be at least 65 cm. If a connection tube composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source. In the case of assembly of the appliance in the suction version prepare the hole for evacuation of the air. • We recommend the use of an air exhaust tube which has the same diameter as the air exhaust outlet hole. If a pipe with a smaller diameter is used, the efficiency of the product may be reduced and its operation may become noisier. • Warning: if the bulbs are not working, ensure that they are screwed in fully. • Installation Prior to proceeding with the assembly operations (according to the model that you have purchased), to facilitate handling of the device, remove the grille as indicated in figure 7 or the aluminium panels as indicated in fi gure 8. • The appliance is equipped with 2 air outlets, to be used in accordance with your specific requirements: one is located on the upper part of the appliance and the other at the rear (Fig. 1A). The fl ange D, to which the air exhaust pipe is connected, and a plug B, used to shut off the unused air outlet, are both supplied with the product. • This device may be installed in two diff erent ways: 1. Fixing the hood to the lower part of the wall cabinet (Fig.2) - Make 4 holes in the wall cabinet respecting the measurements indicated in fi gures 2 A-2 C. - Position the hood underneath the wall cabinet and fi x it into place using 4 screws (not supplied) suitable for the type of cabinet. 2. Fixing the hood to the wall (Fig.2). - Make 4 holes in the wall cabinet respecting the measurements indicated in fi gures 2 A-2 B. - Hang the hood on the wall, using the 2 holes H, align it in a horizontal position and fix it definitively to the wall using the two lower safety holes I (Fig. 2B). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be fi xed. • Mounting decorative ducts (optional) -This hood model may have decorative ducts as optional accessories - ask your retailer for information. - Provide the electrical power supply within the space of the decorative duct. - If your appliance must be installed as an extractor version or as a version with an external motor, make sure an air exhaust hole is prepared (fig. 1A - 1C). - Adjust the width of the upper duct support bracket (Fig. 3). Then fix it to the wall so that it is on the same axis as the hood using screws A (Fig.3) and adhering to the distance from the ceiling shown in (Fig. 2 B). Connect the flexible hose (not supplied) to the fl ange D (fi g. 1A). - Put the upper connector F into the lower connector G and hang the decorative ducts on the wall, as indicated in fi gure 4. - Connect the flexible hose to the air exhaust hole made previously (only in the extraction or external motor version). - Pull out the top connector F as far as the bracket and fi x it - 19 - using screws C (Fig.3). -When carrying out the fixing procedures, use only screws and screw anchors which are suited to the type of wall (e.g. reinforced concrete, plasterboard etc.). - If the screws and screw anchors are supplied with the appliance, make sure that they are suited to the type of wall to which the hood must be fi xed. The hood is already prepared for the version with which it was ordered. The versions may be: -Extraction (fig. 1A-5) -Filter (fig. 1B-6-10). - If the hood is an extractor model, the lever C must be positioned as indicated in figure 5. - If the hood is a filter model, the lever C must be positioned as indicated in figure 6. • Extractor version The appliance expels the fumes through an outside wall or a duct. It is necessary to buy a telescopic pipe in accordance with the standards in use (inflammable) and connect it to flange D (Fig 1A). The fl ange D ...
Otros modelos de este manual:Campanas - KD-N3 (1.27 mb)