Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
– Clean the appliance surfaces and controls with a soft, damp cloth, washing-up liquid or a mild window cleaner only. – Do not scrape off dried dirt, but moisten with a damp cloth. – Clean carefully in the area of the controls to avoid liquid from getting into the electronics. NOTE: Clean the stainless steel surfaces in the direction of the ground surface only! Do not use stainless steel cleaner for the control buttons! Metal-mesh grease filters • The metal-mesh grease filters absorb the grease particles from the kitchen fumes. • The filter mats consist of fire-proof metal. RISK OF FIRE As the filters become more saturated with greasy residue, the flammability increases. The function of the extractor hood may also be impaired. • The risk of fire is prevented by cleaning the metal-mesh grease filters in good time. • When cleaning the grease filters, also remove grease deposits from the accessible parts of the housing with a damp cloth. Cleaning the metal-mesh grease filters ... • Under normal operation (daily 1 to 2 hours), the metal-mesh grease filters must be cleaned 1x month. ... in the dishwasher • The metal-mesh grease filters can be cleaned in the dishwasher. Slight discolouration may occur but this will not affect the function of the grease filters. • The filters must be placed loosely in the dishwasher. They must not be wedged in. NOTE: Do not clean heavily saturated metal- mesh grease filters together with utensils. ... by hand • When cleaning by hand, soak the grease filters in a hot detergent solution, brush off the dirt, rinse thoroughly and leave to dry. • Do not use any aggressive, acidic or alkaline cleaning agents. • If dirt is particularly stubborn, we recommend using a special grease solvent spray.This can be ordered via the Online Shop. 26 Removing and installing the grease filters Activated carbon filters bind the odours in circulating-air mode. Installing and removing the activated carbon filters 1. Remove the grease filters (see Removing and installing the metal-mesh grease filters). 2. Insert the activated carbon filter. 3. Lock the catch. 4. Reinsert the grease filters (see Removing and installing the metal-mesh grease filters). Changing the activated carbon filter Under normal operation (daily 1 to 2 hours) the activated carbon filters must be replaced approximately 2x year. The activated carbon filter is available from specialist outlets, customer service or the Online Shop (see Optional accessories). Use original filters only. Activated carbon filters do not contain any pollutants. They can be disposed of in the household refuse. Before removing and installing the grease filters, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Removing and installing the metal-mesh grease filters 1. Open the lock and fold down the grease filters. In doing so, hold the underside of the grease filters with your other hand. (for appliances with edge extraction) 2. Clean the grease filters. 3. Reinsert the cleaned grease filters. Changing the bulbs • Before changing the bulbs, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! • The description of changing the bulbs applies to several appliance models. NOTE: Observe the warranty regulations in the enclosed service booklet. Changing the halogen bulbs Halogen bulbs become very hot during operation. Even some time after the appliance has been switched off, there is still a risk of burns! • Before changing the halogen bulbs, ensure that they have cooled down fully. 1. Carefully remove the bulb ring with a suitable tool. 2.Replace the defective bulb with a new one of the same type and equivalent power (see rating plate). NOTE: When inserting halogen bulbs, do not touch the glass tube. Therefore use a clean cloth when inserting the bulb. 3. Reinsert the bulb cover. 4. Restore the power supply by inserting the mains plug or switching on the fuse. Changing the filament bulbs 1. Lift the bulb cover slightly. 2. Push the bulb cover towards the middle of the appliance. 3.Replace the defective bulb with a new one of the same type and equivalent power (see rating plate). 4. Reinsert the bulb cover. 5. Restore the power supply by inserting the mains plug or switching on the fuse. NOTE: If the light does not function, check whether the bulbs have been inserted correctly. • Defective bulbs should be replaced immediately to avoid overloading the remaining bulbs. Installation instructions • Prior to installation, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Exhaust-air mode • The exhaust air is conveyed upwards via a ventilation shaft or directly through the outer wall to the exterior. NOTE: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating appliances. • Before conveying the exhaust air into a non-functioning smoke or exha...
Otros modelos de este manual:Campanas - CD637250/01 (1.69 mb)
Campanas - CD639250/01 (1.69 mb)
Campanas - CD646550/01 (1.69 mb)
Campanas - CD649550/01 (1.69 mb)