Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Use only a pressureregulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 100 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury. Never use gasoline or other flammable liquids to clean the tool. Never use the ! DANGER tool in the presence of flammable liquids or gases. Vapors could ignite by a spark and cause an explosion which will result in death or serious personal injury. Always remain in a firmly balanced position when using or handling the tool. Do not remove, tamper with, or otherwise cause the Work Contact Element (WCE) or trigger to become inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result. Do not touch the trigger unless driving fasteners. Never attach air line to tool or carry tool while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. Warning indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Always disconnect the tool from the power source when unattended, ! WARNING performing any maintenance or repair, clearing a jam, or moving the tool to a new location. Always reconnect the air line BEFORE loading any fasteners. Do not load the tool with fasteners when either the trigger is depressed or the Work Contact Element (WCE) is engaged. The tool could eject a fastener causing death or serious personal injury. Always fit tool with a fitting or hose coupling on or near the tool in such a manner that all compressed air in the tool is discharged at the time the fitting or hose coupling is disconnected. Do not use a check valve or any other fitting which allows air to remain in the tool. Death or serious personal injury could occur. Never place hands or any other body parts in the fastener discharge area of the tool. The tool might eject a fastener and could result in death or serious personal injury. Never carry the tool by the air hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. Operating Instructions Model CHN104 • REQUIRES: 0.8 SCFM with 10 fasteners per minute @ 90 psi • AIR INLET: 1/4” NPT • FASTENER SIZE RANGE: 3/8” to 1 1/4” • MAGAZINE CAPACITY: 100 fasteners per load, 18 gauge • STAPLES: 1/4” crown • WEIGHT: 2 lbs., 15 oz. • LENGTH: 10 1/2” • HEIGHT: 9 1/2” • MAXIMUM PRESSURE: 100 psi • PRESSURE RANGE: 60 - 100 psi Tool Components And Specifications Cap exhaust O CO2 100 psi MAX. Warning label Latch button Magazine Fastener discharge area Work contact element (WCE) Trigger Quick clear nose Adjustable depth control (not visible) 6-Sp Manual de Instrucciones Modelo CHN104 Como usar la Herramienta (Cont.) 8. Asegurese de que el gatillo y el elemento de contacto de trabajo (WCE) se muevan libremente hacia arriba y hacia abajo sin adherirse ni trabarse. Servicio Tecnico Si desea hacer alguna pregunta referente a la reparacion u operacion de las herramientas, o para solicitar copias adicionales de este manual, sirvase llamar a nuestro numero especial, 1-800- 543-6400. Sujetadores y Piezas de Repuesto Use solamente sujetadores Campbell Hausfeld originales calibre 16 (o su equivalente) - (vea la informacion sobre intercambio de sujetadores). El desempeno de las herramientas, la seguridad y la duracion pueden disminuir si no se utilizan los sujetadores adecuados. Cuando ordene piezas de repuesto o sujetadores, especifique el numero de la pieza. Para reparar la herramienta La herramienta debe ser reparada unicamente por personal calificado, y deben usar piezas de repuesto y accesorios originales Campbell Hausfeld, o ! ADVERTENCIA piezas y accesorios que funcionen de manera equivalente. Para colocarle los sellos Cada vez que repare una herramienta debera limpiarle y lubricarle las partes internas. Le recomendamos que use Parker O-lube o un lubricante equivalente en todos los anillos en O. A cada anillo en O se le debe dar un bano de lubricante para anillos antes de instalarlos. Igualmente, debera ponerle un poco de aceite a todas las piezas que se mueven y munones. Finalmente, despues de haberla ensamblado y antes de probar la herramienta debera ponerle unas cuantas gotas de aceite sin detergente 30W u otro aceite similar, en las lineas de aire. 3 General Safety Information (Continued) Always assume the tool contains fasteners. Respect the tool as a working implement; no horsep...
Otros modelos de este manual:Refrigeradores - CHN104 (2.53 mb)