Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
• The LED display for the lower zone will flash. • The preset temperature for the upper zone is 10.C / 50. F and for the lower zone is 16.C / 60. F. • To change the temperature display from Fahrenheit to Celsius, or Celsius to Fahrenheit, press and hold the up and down • buttons simultaneously for five seconds. • To view the set temperature in either zone, touch the up or down button at any time and the set temperature will flash in the LED display for five seconds. Optimal temperature selection Whilst wine is best stored at temperatures between 13 and 15. C, your wine can also be stored at drinking temperature, for red wine this is between 15 and 17. C, and for white wine between 12 and 13. C. To use the internal light • Press the light button to switch the light on or off. c F C/ F 1 2 3 4 Key: 1 – Light button 2 – Temperature set button 3 – Up button 4 – Down button Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water. Do not put them in the dishwasher. • Ensure that the cloth is only moist when cleaning the control panel and electrical parts, and that all water is thoroughly dried off before reconnecting the power. • Once cleaning is complete, reconnect the mains electrical supply. • If the appliance is not to be used for prolonged periods of time, unplug and clean the appliance thoroughly. The door should be left slightly ajar to prevent the formation of odours or condensation. Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working. • The ambient temperature is between 5-38.C. The appliance is working, but not very well, check • The appliance is not overloaded. • The thermostat is set to an appropriate temperature. • The door is closing properly. • The door gasket is sealing properly • There is enough ventilation at the side and rear walls. • The ambient temperature is between 5-38.C. The appliance is noisy, check • The appliance is level and stable. • The cooling gas will make some noise, even when the compressor is not running. • During operation, it is normal for the fan to run, even when the compressor is not running. The light does not work, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The light button is not set to off Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CDA Customer Care. The door will not close properly, check • The appliance is level and stable. • If the door has been removed, it may not have been correctly refitted • The door seal is dirty • The shelves are not positioned correctly The display show “EL” or “EH” • The temperature sensor has failed Installing the wine cooler This appliance is intended to be built in to a kitchen cabinet. This appliance should be installed in a well ventilated, dry room. This appliance must not be installed: 1. In direct sunlight 2. Adjacent to a heat source (oven or radiator) 3. Below a hob unit Place your wine cooler in a location which is strong enough to support its weight when fully loaded. To level the wine cooler, adjust the front levelling legs at the bottom of the wine cooler. Ensure that there is an adequate flow of air at the rear of the cabinet, as shown in the diagram. Please note that a plinth vent of at least 200 cm. is recommended to allow for sufficient ventilation. If a ventilation intake is provided elsewhere, the plinth vent may not be necessary IMPORTANT: Failure to follow the instructions regarding installation and ventilation may invalidate the warranty supplied with your appliance. To ensure the proper functioning of the appliance, air vents should never be blocked or covered. 537 540 459 445 592 18 447 - 452 550 - 560 560 - 568 min. 200cm2 min. 200cm. 537 540 884 871 592 18 873 - 878 550 - 560 560 - 568 min. 200cm2 min. 200cm2 FWV450 FWV900 To install the handle IMPORTANT: Do not overtighten the screws, and do not use power tools to install the handle. 1. Carefully remove the door seal on the side you wish to install the handle. 2. Insert the screw from the inside of the door frame and screw it in to the handle, using the screws, lock washers and ...
Otros modelos de este manual:Refrigeradores - FWV900 (395.45 kb)