Votos - 3, Puntuación media: 4 ( )

Fabricar: CDA Tamaño del archivo: 391.1 kb Nombre del archivo: Idioma del manual:

• The preset temperature is 12.C / 54. F. • To view the set temperature, touch the up or down button at any time and the set temperature will flash in the LED display for five seconds. Temperature display To change the temperature display from Fahrenheit to Celsius, or Celsius to Fahrenheit, touch the F./C. selection button. Optimal temperature selection Whilst wine is best stored at temperatures between 13 and 15. C, your wine can also be stored at drinking temperature. For red wine this is between 15 and 17. C, and for white wine between 12 and 13. C. To use the internal light • Press the light button to switch the light on or off. Key: 1 – Power on/off 2 – Light button 3 – Temperature display 4 – Up button 5 – Down button 1 3 4 5 fig. 4 Temp. c F C/ F Temp. c F 2 Key: 6 – °F/°C selection button 7 – Light button 8 – Temperature display 9 – Up button 10 – Down button 6 7 8 9 10 Left zone Right zone 5 Use Humidity Control (all models except FWC151) The wine coolers are equipped with a humidity control system to maintain optimal humidity within the wine cooler. Fill the humidity reservoir approximately 3/4 full with water. Place the reservoir on the runners on the top shelf as shown in fig. 5. Ensure it is located correctly to prevent water spillage. Check the water level regularly and refill if required. fig. 5 Temperature display The temperature display will show the current internal temperature. The display flashes: • When a different temperature is being set • If the internal temperature is +/- 5. away from the set temperature. This serves as a warning to prevent damage to the contents of the appliance should the temperature be too high. Dynamic Cooling and Silent modes The appliance has two different running modes. • Silent mode Once the required temperature is reached, the appliance will run without the fan. • Dynamic cooling mode The fan cycles on and off to circulate the air even after the required temperature is reached. This ensures consistent humidity and temperature distribution in the wine cooler, creating perfect conditions for long term storage. Dynamic cooling is the factory preset mode. To change to silent mode, touch and hold the up key for approximately five seconds. The wine cooler will beep three times to confirm silent mode is on. To change to dynamic cooling mode, touch and hold the down key for approximately five seconds. The wine cooler will beep five times to confirm dynamic cooling is on. Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water. Do not put them in the dishwasher. • Ensure that the cloth is only moist when cleaning the control panel and electrical parts, and that all water is thoroughly dried off before reconnecting the power. • Once cleaning is complete, reconnect the mains electrical supply. • If the appliance is not to be used for prolonged periods of time, unplug and clean the appliance thoroughly. The door should be left slightly ajar to prevent the formation of odours or condensation. Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working. • The ambient temperature is between 16. to 38.C. The appliance is working, but not very well, check • The appliance is not overloaded. • The thermostat is set to an appropriate temperature. • The door is closing properly. • The door gasket is sealing properly • There is enough ventilation at the side and rear walls. • The ambient temperature is between 16. to 38.C. The appliance is noisy, check • The appliance is level and stable. • The cooling gas will make some noise, even when the compressor is not running. • During operation, it is normal for the fan to run, even when the compressor is not running. The light does not work, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The light button is not set to off Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CDA Customer Care. The door will not close properly, check • The appliance is level and stable. • If the door has been removed, it may not have been correctly refitted • The door seal is dirty • The s...

Descargar ahora

Introduzca dos números de la imagen: