Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Tips for saving energy ¦ Install the appliance in a dry, well ventilated room! The appliance should not be installed in direct sunlight or near a heat source ( e.g. radiator, cooker) . If required, use an insulating plate. ¦ Do not block the ventilation openings in the appliance. ¦ Allow warm food and drinks to cool down before placing in the appliance. ¦ Thaw frozen food in the refrigerator compartment and use the low temperature of the frozen food to cool refrigerated food. ¦ Open the appliance as briefly as possible. ¦ Ensure that the freezer compartment door is always closed properly. ¦ Occasionally clean the rear of the appliance to prevent an increased power consumption. ¦ If available: Fit wall spacers to obtain the indicated energy rating of the appliance ( see Installation instructions) . A reduced wall gap will not restrict the function of the appliance. The energy rating may then change slightly. The gap of 75 mm must not be exceeded. en Operating noises Quite normal noises Droning Motors are running ( e.g. refrigerating units, fan) . Bubbling, humming or gurgling noises Refrigerant is flowing through the tubing. Clicking Motor, switches or solenoid valves are switching on/off. Preventing noises The appliance is not level Please align the appliance with a spirit level. Use the height- adjustable feet or place packing underneath them. The appliance is not free-standing Please move the appliance away from adjacent units or appliances. Containers or storage areas wobble or stick Please check the removable parts and re- insert them correctly if required. en Eliminating minor faults yourself Before you call customer service: Please check whether you can eliminate the fault yourself based on the following information. Customer service will charge you for advice – even if the appliance is still under guarantee! Fault Possible cause Temperature differs greatly from the set value. Remedial action In some cases it is adequate to switch off the appliance for 5 minutes. If the temperature is too high wait a few hours and check whether the temperature has approached the set value. If the temperature is too low check the temperature again the next day. Displays do not illuminate. Power failhas been the mains has not bproperly. ure; the fuse switched off; plug een inserted Connect mains plug. Check whether the power is on, check the fuses. Appliance does not respond when buttons are pressed. “ Button lois switcheck” function d on. Cancel button lock ( see “ Fascia” ) . Warning signal sounds. The alarm button is lit. Fault – the freezer compartmwarm! Fig. 2/4 ApplianceVentilation openings have been covered. Too much placed in compartment is too To switch off the warning signal, press the alarm button 4. is open. Close the appliance. Ensure that there is adequate ventilation. food was the freezer ent at once. Do not exceed max. freezing capacity. When the fault has been eliminated, the alarm button goes out shortly afterwards. en Fault Possible cause Remedial action Appliance is not cooling, temperature display and light are lit. Showroom mode is switched on. Hold down alarm button, Fig 2/4, for 10 seconds until an acknowledgement signal sounds. After a short time check whether your appliance is cooling. Freezer compartment door was open for a long time; temperature is no longer reached. The evaporator (refrigeration generator) in the No Frost system is covered in thick ice and can no longer be defrosted fully automatically. To defrost the evaporator, remove the frozen food with the compartments, insulate well and store in a cool location. Switch off the appliance and move it away from the wall. Leave the appliance door open. After approx. 20 min. the condensation begins to run into the evaporation pan, at the rear of the appliance. Fig. * To prevent the evaporation pan from overflowing in this case, mopupthe condensation with a sponge. The evaporator is defrosted when the water stops running into the evaporation pan. Clean the interior. Switch the appliance back on again. en Appliance self-test Your appliance features an automatic self-test program which shows you sources of faults which may be repaired by customer service only. Starting the appliance self-test 1. Switch off the appliance and wait 5minutes. 2. Switch on the appliance and within the first 10 seconds hold down the super button, Fig. 2/ 2 for 5- 10 seconds until the second warning signal sounds. The self- test programme starts. When the self-test ends and a warning signal sounds twice, your appliance is in working order. If the alarm display 2/4 flashes and 5 acoustic signals sound, there is a fault. Inform customer service. Ending the appliance self- test When the programme has ended, the appliance switches over to normal operation. Customer service Your local customer service canbefound in thetelephone directory or in the customer- service index. Please provide customer service with the appliance product number (E-Nr. ) and production number (FD)...
Otros modelos de este manual:Refrigeradores - GS36NBW30/01 (2.33 mb)
Refrigeradores - GS36NBW30G/01 (2.33 mb)