Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Failure to remove grease may result in grease dripping onto the cart and/or a grease fire in the tray. Lighting the Grill Using the Integral Ignition System · Open Hood before lighting the grill to prevent an explosion from gas buildup. · Always inspect the gas hose and regulator assembly before each use. If the hose is cut, damaged, or shows signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose and regulator assembly must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill. How to light your LP gas grill (See diagram on next page for illustrations) 1) Open Hood and Control Panel Cover. 2) Important: Make sure control knobs are turned “off” first. Open the LP gas cylinder valve by turning the valve counterclockwise until it stops. 3) From the “Off” position, push control knob in on the left burner and turn counter-clockwise until you feel resistance. Pause 4 seconds, then continue turning the control knob until a click is heard and the burner is lit. 4) Light the remaining burners by turning the control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another. Confirm each burner is lit before lighting another burner. 5) If any of the burners do not light, repeat Step 3. The burner should light within three or four attempts. If burner still does not light, try the next burner from left to right. WARNING: If any or all burners fail to light after following Steps 3 & 4, turn all knobs to the “off” position and close the valve on the LP gas cylin der. Wait five minutes; then repeat all of the above lighting procedures. Note: If the burners still fail to light, refer to the Troubleshooting page. The burner can be lit manually. See Manual Lighting of the Grill. 6) After ignition, preheat the grill by turning the control knob to “High” position for 3-5 minutes. The grill should be pre-heated before every cooking session. WARNING: If a burner goes out during the cooking cycle, turn all knobs to the “off” position and close the The hood should be closed during preheating. valve on the LP gas cylinder. Open hood and wait five minutes before attempting to relight the grill. Always leave the Control Panel Cover open during use to prevent excess heat buildup and damage to your grill. 18 Manual Lighting of the Grill Manual Lighting of the Grill 4) Locate the control knob that corresponds to the match lighting hole that you are using. Push in and turn the control knob counter-clockwise until a click is heard. WARNING: If the burner fails to ignite after · Open Hood before lighting the grill to prevent an following the above procedure, turn all the knobs explosion from gas build-up. to · Always inspect the gas hose and regulator the “off” position and close the valve on the LP gas assembly before each use. If the hose is cut, cylinder. Wait five minutes and repeat all of the above damaged, or showing signs of excessive abrasion manual lighting procedures. If the grill still fails to light, or wear, do not use the LP gas grill. Contact the see the Troubleshooting page. manufacturer, as the hose must be replaced with an assembly specified by the manufacturer 5) Light the remaining burners from left to right by turning the prior to further use of the LP gas grill. control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another. Confirm each burner is lit before lighting another burner. 6) After ignition, burners should be burned at the “high” position How to manually light your LP gas grill for 3-5 minutes in order to preheat the grill. This process 1) Open Hood and Control Panel Cover. should be done before every cooking session. The hood 2) Important: The LP gas cylinder valve must be should be closed during preheating. opened first before turning the control knobs on the WARNING: If a burner goes out during the cooking grill. Turn the LP cylinder valve counter-clockwise cycle, turn all knobs to the “off” position and close the until it stops. valve 3) Using the match Wire Holder (Item 25), light a on the LP cylinder. Open hood and wait five minutes match and insert it through the match-lighting hole before attempting to relight the grill. Always leave Control underneath the left side table on the grill Body. Hold Panel Cover open during use to prevent excess heat buildup lit match near burner(See figure below). and damage to your grill. 19 Check Your Flame End of Cooking Session Check Your Flame End of Cooking Session Your burners have been preset by the manufacturer for optimal flame performance. A blue flame, possibly with a small yellow tip, is the result of the optimal air and LP gas mixture. (See diagram below) Yellow Tip Blue Flame The flame should be checked before the initial cooking session and periodically throughout the grilling season, especially after storing the grill o...
Otros modelos de este manual:Greeley - ESSENTIALS 8353 (1.19 mb)
Greeley - ESSENTIALS 8353 (1.19 mb)