|
Resumen del manual
Tighten Phillips screw at air shutter. 22. Replace burners into grill. Tighten two (2) Phillips screws at end of each burner. 23. Ignite burners on grill to verify burner flame characteristics. Installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. In Canada, installation shall be in accordance with CAN/CGA-B149.1 Natural Gas Installation Code, and local codes where applicable. Contact your local gas company for code regulations, recommended procedures, and the installation of your grill’s gas supply line. Caution: The grill and its individual shutoff valve must be disconnected from the gas supply piping system during any system pressure testing at test pressures in excess of 1/2 PSIG. Caution: The grill must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG. SBB00101-1-1007 Page 15 Page 16 SBB00101-1-1007 OPERATION Checking for Gas Leaks Check for gas leaks every time you connect your Superb by Broilmaster® propane gas grill to a Propane gas cylinder, when a connected cylinder has not been used recently, or when either a natural or propane grill is being used for the first time. Caution: Do not use a flame when checking for leaks. Checking for leaks with a flame may lead to a fire or explosion, resulting in property damage or personal injury. To check for gas leaks: 1. Use dish washing liquid and a little water to make a soapy solution. 2. Turn OFF the knobs on the control panel. 3. Turn ON the gas at the supply or cylinder. A hissing sound indicates a leak. Turn OFF the gas and repair the leak. 4. Apply the soapy water solution to all gas connections. 5. Look for bubbles. Bubbles indicate a leak. 6. If there are bubbles turn OFF the gas and repair the leak. 7. Turn the gas back ON and repeat the above procedures until all leaks are repaired. Air Shutter Adjustment 1. Remove cooking grids and flame tamers from grill. 2. Ignite burners on grill and observe flame pattern. If flame is yellow in color or flame is lifting off burner the air shutter on burner will require adjustment. 3. Turn gas OFF and allow the grill to cool. 4. Loosen two (2) Phillips screws at end of each burner. Lift upward and pivot burner out of grill. 5. Loosen Phillips screw at air shutter. Open air shutter for a yellow flame or close air shutter for a lifting flame. Tighten Phillips screw at air shutter. 6. Replace burners into grill. Tighten two (2) Phillips screws at end of each burner. 7. Ignite burners on grill to verify burner flame characteristics. OPERATING INSTRUCTIONS Using the Ignitor Caution: If a burner fails to light after 5 seconds, turn the burner OFF for 5 minutes, to allow the gas to clear, then try again. Attention: You should use the center burner(s) to ignite the first burner, then move from center to both sides. Attention: The control knob that is second from left side of grill is for the rotisserie. See Rotisserie Operation on page 12. 1. Turn the right control knob clockwise to the OFF position. 2. Turn ON gas supply to the grill. 3. With the grill lid open, push and turn the right control knob counterclockwise to HI. 4. Push and hold in the ignitor button until the right burner ignites. 5. If right burner does not ignite, turn right control knob clockwise to the OFF position. Turn OFF gas supply to grill. Refer to Troubleshooting section in this manual. OPERATING INSTRUCTIONS Using Matches Caution: If a burner fails to light after 5 seconds, turn the burner OFF for 5 minutes, to allow the gas to clear, then try again. Attention: You must use the control knob on the right side of the grill to ignite the first burner. The second burner to be ignited will be the second from right side of grill and so forth, always moving from right to left. Attention: The control knob that is second from left side of grill is for the rotisserie. See Rotisserie Operation on page 12. 1. Turn the right control knob clockwise to the OFF position. 2. Turn ON gas supply to the grill. 3. Open the grill lid. 4. A match holder is attached on the inside of the right door. Place a match into match holder. Insert burning match through the lighter hole on right cart side. Place burning match adjacent to right burner. Figure 19 5. Push and turn the right control knob counterclockwise to HI. 6. If right burner does not ignite, turn right control knob clockwise to the OFF position. Turn OFF gas supply to grill. Refer to Troubleshooting section in this manual. OPERATION (cont.) Before Cooking Before cooking on a grill for the first time, it should be “burned off” to remove any oil residue from the manufacturing process. 1. Raise the grill lid. 2. Light grill burners. 3. Burn on HI for ten minutes. 4. Close the lid and burn on HI for an additional ten minutes. 5. Turn OFF gas. The grill is now ready for use. Preheating Before cooking ...
Otros modelos de este manual:Greeley - SBG2501-1 (2.5 mb)
Greeley - SBG2801-1 (2.5 mb)