Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Disconnected cylinders must have a threaded valve plug tightly installed and must not be stored in any building, garage, or other enclosed area. Flammable materials (gasoline, grill covers, etc.) must not be stored in the cylinder enclosure. Always store Propane cylinders in a secured upright position, out of reach of children. Connection Requirements Caution: Never use Liquid Propane (LP) gas in a grill designed for Natural gas, or Natural gas in a grill designed for Liquid Propane gas. Questions regarding different types of gases should be directed to your local gas supplier. SBB00101-1-1007 Page 13 Page 14 SBB00101-1-1007 PROPANE GAS GRILLS (cont.) Installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. In Canada, installation shall be in accordance with CAN/CGA-B149.2 Propane Installation Code, or CAN/CGA-B149.1 Natural Gas Installation Code, and local codes where applicable. Consult your local gas supplier or propane gas dealer for code regulations and recommended procedures. Warning: Superb by Broilmaster® Gas Grills require Liquid Propane (LP) cylinders equipped with an Overfill Protection Device (OPD). An overfilled or improperly filled Propane cylinder can be dangerous. Always use the pressure regulator and hose assembly supplied with your Propane gas grill. Note: Not all valve and cylinder combinations are compatible. Check warning tag on valve and cylinder as well as external fitting threads. All Broilmaster pressure regulators and hose assemblies require Propane cylinders with a Type 1 connection device as illustrated. See Figure 16. Pressure Regulator and Hose Assembly The pressure regulator has an outlet pressure of not more than eleven (11”) inches water column. It must be connected to the Propane gas cylinder’s female valve outlet before the grill can be operated. Caution: Operation of a propane gas grill without the pressure regulator and hose assembly will cause gas leaks which could lead to fire or explosion, resulting in property damage or personal injury. The pressure regulator’s fitting must remain clean and free of nicks and scratches. A dirty, nicked or scratched fitting can cause a gas leak, resulting in an explosion or fire. Use only genuine Broilmaster® replacement parts unless otherwise specified by the manufacturer. Connecting to Propane Gas / Cylinder Retention Means Attention: Propane gas cylinders that are acceptable for use with this grill must comply with “Cylinder Requirements” section and “Connection Requirements” section (Pages 13-14.) Lift up the tank ring. Position the cylinder in the opening at the bottom of the cart then fit the tank ring out side of the tank. See Figure 15. Figure 15 Attach the pressure regulator to the Propane gas cylinder’s valve using the plastic handwheel. Tighten in a clockwise motion to achieve a gas tight seal. See Figure 16. Figure 16 Caution: Do not use a wrench or any other tool to tighten. Use of a wrench or other tool will damage the plastic handwheel. Fit hose to the hook inside of the right side panel. See Figure 17. Figure 17 To disconnect the Propane gas cylinder, turn OFF the cylinder’s valve and the grill’s control valve. Remove the regulator by turning the plastic handwheel counterclockwise. Clockwise GAS CONVERSION TO NATURAL GAS A conversion kit to natural gas is included with your grill. 1. Remove cooking grids and flame tamer from grill. 2. Use allen wrench supplied in conversion kit to remove control knobs. 3. Remove control panel (4 Phillips screws). Figure 18 4. Use a 7mm socket or wrench to remove all LP gas orifices marked 1.02 from gas valves. 5. Install natural gas orifices marked 1.51 into gas valves. Apply pipe compound to threads on orifices prior to installation. 6. Attach left side of control panel to grill with two (2) Phillips screws from Step 3. Carefully insert left burner orifice into left burner. Continue to carefully insert the remaining orifices into the burners. Attach right side of control panel to grill with two (2) Phillips screws from Step 3. 7. The low input adjustment screws are located inside the main burner valve stems. Use small screwdriver supplied in conversion kit to turn each adjustment screw clockwise 1/4 turn (90 degrees). Attention (SBG2501 and SBG2801 Only): The valve stem that is second from the left side of the grill is the rotisserie valve stem and it will not be adjusted. 8. Remove rotisserie burner back cover (5 Phillips screws - four on the back and one on inside top of the back of the grill). 9. Use a 14mm wrench or adjustable wrench to remove LP gas rotisserie orifice marked 0.84 for SBG2501 and 1.02 for SBG2801 from orifice fitting. 10. Install natural gas rotisserie orifice marked 1.18 for SBG2501 and 1.51 for SBG2801 into orifice fitting. Apply pipe compound to threads on orifice prior to installation. 11. Remove the hose and regulator from the gas connection on grill with an adjustable wrench. 12. Connect the gri...
Otros modelos de este manual:Greeley - SBG2500-1 (2.5 mb)
Greeley - SBG2801-1 (2.5 mb)