Speaker Kit: SPK-6L Description The SPK-6L is a speaker option for the Isys® TPS-6L Wall Mount Touchpanel. Adding the SPK-6L provides amplification of external AV sources, and supports programmable intercom functionality in combination with the touchpanel's built-in microphone. Refer to the latest version of the TPS-6L Operation & Installation Guide (Doc. 6556) for information on using the SPK-6L. The manual is available from the Crestron website (Setup Supplied Hardware The SPK-6L Speaker Kit c

©2008 Crestron Electronics, Inc. Contents Pre-Construction Wall Mount Back Box: BB-6X-DSW 1 Description.................................................................................................................................1 Setup..........................................................................................................................................5 Assembly.................................................................................................................

©2008 Crestron Electronics, Inc. Contents Docking Station for the TPS-6X: TPS-6X-DS 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Specifications..............................................................................................................2 Physical Description.......

• Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades wit

Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Description Mud Mount Kits are the preferred mounting option for the TPS-6X-DSW when the cutout made in the drywall for docking station installation is too large. These kits provide support for additional plastering that can be applied to hide large irregularities in the cutout. NOTE: If mounting into a material other than drywall (for example, wood lectern, concrete or rock) use the cutout template, available in the post-construction k

• If mounting into the BB-6X-DSW, bend the flanges back as far as they can go. 6. Use four standard drywall screws (length should not exceed drywall thickness by more than 1/2 inch) to secure the mud ring plate to the rest of the assembly. The screws pass through the clearance holes in the PMK-6X-DSW (or BB-6X-DSW) and are secured in the extruded holes of the adjustment plates. 7. Verify that the mud ring plate is level. NOTE: Do not overtighten screws. Doing so may over-dimple or rip the mud ri

The “TMK-6X-DSW Procedure” starts below and the “WMKT-6X-DSW Procedure” starts on page 6. Be sure to review each procedure before starting. TMK-6X-DSW Procedure This section provides the necessary steps for the assembly of the TMK-6X-DSW with either the BB-6X-DSW or PMK-6X-DSW. It is assumed that the BB-6X-DSW or PMK-6X-DSW has been secured to the stud according to the instructions in the latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively). It is also assumed tha

For concrete and rock mounting material, allow for proper ventilation before mounting the TPS-6X-DSW. There are two Trim Ring Mount Kits. The TMK-6X-DSW is a pre-construction accessory. Pre-construction refers to framed walls prior to hanging drywall. This accessory must be used with either the Pre-Construction Mount Kit (PMK-6X-DSW) or Wall Mount Back Box (BB-6X-DSW). The WMKT-6X-DSW is a post-construction kit. Post-construction refers to framed walls with drywall hung. This accessory is design

WARNING: Charge the touchpanel in a well ventilated area away from sparks and open flame. Do not use the touchpanel near heat sources such as radiators, heat registers, stoves or other apparatus. CAUTION: Avoid accidental shorting of the electrical contacts to prevent possible damage to the touchpanel. NOTE: Docking station contacts can be cleaned with electrical contact cleaner (not included). Follow directions that come with the cleaner. Further Inquiries If you cannot locate specific informat

3.63 in(9.22 cm) 2.25 in(5.72 cm) 6.25 in(15.88 cm) FROM (included) AC POWER PACK WARNING: To avoid possible physical harm, damage to the TPMC-4XG-DS or touchpanel, use only the included power pack (100-240 VAC, 50/60 Hz) when charging. WARNING: Charge the touchpanel in a well ventilated area away from sparks and open flame. Do not use the touchpanel near heat sources such as radiators, heat registers, stoves or other apparatus. CAUTION: Avoid accidental shorting of the electrical contacts to pr