Votos - , Puntuación media:
(
)
)
Fabricar: Kenwood
Tamaño del archivo: 588.59 kb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
terminal. "Connecting Cables to Terminals". The ignition and battery cable are incorrectly connected. Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". The TEL mute function does The TEL mute cable is not connected properly. Connect the cable correctly, referring to the section on not work. "Connecting Cables to Terminals". The TEL mute function turns The TEL mute cable is touching a metal part of the car. Pull the TEL mute cable away from the metal part of the on even though the TEL mute car. cable is not connected. — 31 — English Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION A CD ejects as soon as loaded. The CD is upside-down. The CD is quite dirty. Load the CD with the Clean the CD, referring to the (see page 5). The sound skips on a CD. The CD is scratched or dirty. Clean the CD, referring to the section (see page 5). The specified track does not play. Random play has been selected. Turn off the random play function. Can’t remove disc. The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. The disc can only be removed within 10 minutes ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. Free switching of the sound quality. The System Q function is set on Scan mode. Refer to the “System Q” page and switch it to a function other than Scan mode. (see page 8) — 32 — Troubleshooting CD/External PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No cable has been connected Connect the cable to the be selected. terminal on the unit. the unit. The specified disc does not The specified CD is very dirty. Clean the CD. play, but another one plays instead. The CD is upside-down. Load the CD with the labelled side The disc is loaded in a different slot from Eject the disc magazine and check the number specified disc. The disc is severely scratched. Try another disc instead. The sound skips. Something is touching the disc changer. Remove whatever is touching it. The CD is scratched or dirty. If skipping happens at the same place when the car is stopped, something is wrong with the CD. Clean the CD. The display shows that the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see page 4) . changer is being played, but no sound can be heard. The specified track does not Random play or magazine random play has been Turn off the random play or magazine random play play. selected. function. Track repeat, disc repeat, track The setting is not cancelled. The settings for these functions remain on until the scan, random play, and setting to off or the disc ejected, even if the power is magazine random play start by turned off or the source changed. themselves. Cannot play CD-R or CD-RW. Finalization processing is not being conducted for CD- Conduct finalization processing with CD recorder. R/CD-RW. A non-compatible CD changer is being used to play the Use a CD changer compatible with CD-R/CD-RW to play. CD-R/CD-RW. If the following situations, consult your nearest service centre: • Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display Mode. • Even though no device ( KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes. — 33 — English Troubleshooting The following recommended EJECT No disc magazine ] Load the disc magazine No CD in the unit. ] Insert the CD. NO DISC No disc has been loaded in the ] Load a disc into the disc magazine. E-04 No disc has been loaded in the disc ] Load a disc into the disc magazine. The CD is very dirty. The CD is upside-down. ] Clean the CD and load it correctly. BLANK Nothing has been recorded on the MD. NO TRACK No tracks are recorded on the MD, although it has a NO PANEL The faceplate of the slave unit being connected to this unit ] Replace it. E-77 The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "E- 77", code does not disappear, E-99 Something is wrong with the disc magazine. Or the unit is malfunctioning ] Check the disc magazine. And then, press the reset button on the unit. If the "E- 99" code does not disappear, consult your nearest service centre. HOLD The protective circuit in the unit activates when the temperature inside the automatic stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature the disc starts playing again. IN If this indicator blinks, the CD player is malfunctioning. ] Eject the CD and try inseting it again. If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected. — 34 — Specifications Specifications FM tuner section Frequency range ..............87.5 MHz Usable sensitivity (S/................................. 0.7 .V/75 . Quieting Sensitivity (S/.............................. 1.6 ....
Otros modelos de este manual:Unidad - KDC-305RA (588.59 kb)
Unidad - KDC-305RG (588.59 kb)
Unidad - KDC-3090RG (588.59 kb)
Unidad - KDC-4090R (588.59 kb)