Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Then bend cover forward and insert front tab in slot provided on mounting plate. Tab Slot P_ate ................................. ,,, 1111 , [H ", , _llJ,,,m,,,, ,,1 II I 8 Assembly Hit I i, ,,i I III I ,I, I IIIlllll II I , H,,I STEP 5 Tighten the Chain and Cable , ,, , H,,"H I I="= HI ,I,,H,, , .................................. Loosen Lock Tighten CAUTION: Keep the turned. chain from twisting as nuts are PROCEDURE: Thread the outer nut toward shown. (Loosen inner nut first, if necessary.) troltey as Tro({_ Tension is correct when the chain is approximately 1t2" above the base of the Tee rail, midway between puIley bracket and chassis. To maintain proper lension, make sure inner nut is retightened. Chin Sprocket noise or too tight, can result if chain is either too loose i Base of Tee R_I .,-.--1/ 2 Inch CAUTION: Do not Page 3. overtighten the chain. Refer to ASSEMBLY OF YOUR GARAGE DOOR OPENER IS NOW COMPLETE. BEFORE YOU PROCEED WITH THE INS'I'ALLATION OF YOUR GARAGE DOOR OPENER, BE SURE TO COMPLY WIT_ ALL SAFETY RULES. KEEP GARAGE DOOR BALANCED. STICKING OR BINDING DOORS MUST BE REPAIRED. THE GARAGE DOOR, DOOR SPRINGS, CABLES, PULLEYS, BRACKETS AND THEIR HARDWARE ARE UNDER EXTREME TENSION AND CAN CAUSE SERIOUS PERSONAL INJURY. DO NOT ATTEMPT TO LOOSEN, MOVE OR ADJUST THEM° CALL A GARAGE DOOR SERVICEMAN. DO NOT WEAR WATCHES, RINGS OR LOOSE CLOTHING WHILE INSTALLING OR SERVICING A DOOR OPENER. % AS YOU PROCEED WITH THE REMAINING INSTRUCTIONS IN THIS OWNERS MANUAL, YOU MAY FIND IT HELPFUL 3"0 REFER TO THE FOLLOWING ILUJSTRATION OF THE FULLY ASSEMBLED AND INSTALLED GARAGE DOOR OPENER° : ...............iii1,_ ,i H N HHHI llJ,ll,I, ................................. HI H HI,HHI Power Cord Light Arm Lens OO Eme_ency Chessis Trolley Release Curved Door oDoor Arm .... ,ll, ii ii i i i ,, ii ii,ii,i i i , _,ul,,,.., ii ii ,i IS RECOMMENDED THAT THE OPENER BE INSTALLED 7 FEET OR MORE ABOVE FLOOR WHERE SPACE PERMITS. CERTAIN INSTALLATION PROCEDURES VARY ACCORDING TO GARAGE DOOR TYPES. WHERE THE DIFFERENCES OCCUR, BE SURE TO FOLLOW ONLY THOSE INSTRUCTIONS WHICH APPLY TO YOUR DOOR CONSTRUCTION. installation i,! ,i ii, iiii i, ,i,,i i, iiii1,11 i i i i , ii iiii...:: ....... iii iiii L ii iiiiiii ,11 iiiii Position and Instafl Header Bracket STEP 1 installation procedures vary according to garage door types. Follow only those instructions which apply to your door as tllustratedo i iiii i IL iii i .... := THE HEADER BRACKET MUST BE RIGIDLY FASTENED TO THE HEADER WALL. REINFORCE THE WALL WiTH 2x4 IF NECESSARY. FAILURE TO COMPLY MAY RESULT IN IMPROPER OPERATION OF SAFETY REVERSE SYSTEM (SEE PAGE 18)+ INSTALLATION centerline of garage door. Extend line onto header wall SECTIONAL DOOR AND above the door. l-PIECE DOOR WITH TRACK 1o With the door closed, locate and mark the vertical 2. Locate height for header bracket by opening door to highest point of travel as shown. Draw an intersecting horizontal line on header wail 2" above high point. This SECTIONAL DOOR ONE-PIECEDOOR height provides travel clearance for top edge of door. CURVED TRACK HORIZONTAL TRACK Ceiling JAMB HARbWARE NOTE: When the headroom is not sufficient for 2" Header clearance, the bottom edge of bracket may be placed _cket parallel to the high point of travel Door Clearance Brackets ere designed for low headroom installations (page 4). They replace top brackets and milers on the garage door, thereby Track lowering the high point of door travel. Installation instructions are contained in the accessory carton. {_ackel . / i / I" I I ,,_ .F H_hest P_nt o! y "Travel ii,J, IIIIL, i irlll,lll ijlll ii , iii iiiiii1,1111 1-PIECE INSTADOOR LLATION WITHOUT TRACK ONE PIECE DOOR ONE PIECE DOOR NO TRACK PIVOT HARDWARE JAMB HARDWARE ..... "NO TRACK HighestPo{nt Header of Trey!! Door 3. Position bracket as shown (bottom edge of bracket on herizortal line). Mark either top and bottom or left and right bracket holes. Drill 3/16" pilot holes and fasten bracket. i ,,,i ,i ii i ri i ir t. Follow instructionsas describedin 1 above. 2. Locateheight for header bracket by opening doot: to highestpoint oftravelas shown.Measure the distance from top of door to floor,Subtractactual height of door. Add 8" tothe remainder.Refer to examplebelow. NOTE: If total numberof inches exceedsthe height available in your garage, use the maximum height possets. On finished ceilings, do not position the bracket closer than 1/2" from ceiling. 3 Measudng frem top of door draw an intersecting horizontal line ontheheaderwallat determinedheight. Position the bottom edge of header bracket on the horizontal line, centeringbracket on verticleline, Mark either topand bottom or left and rightholes°Drill 3/16" pilot holes andfasten the bracket with 5/16"xl-7/8" lag screws as shown above, EXAMPLE Distance from lop of door (at highest pointoftravel) to floor ................. 92" Actual height of door ........................ 88" Remainder ................................. 4" Add .................................
Otros modelos de este manual:La puerta automática - 139.53699SR (2.03 mb)
La puerta automática - 139.53625SR (2.03 mb)