Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
screws (not supplied) to securely @sten the 2x4 to structu.d sqppof_s as shown here and on page t& Ce_r_g He_der Open your door to the highest Tr_:k point of travel as shown Draw an intersecting hodzanta_ line on the header wat/2 above of Trav_ the high point. This height wi_/ provide traw_t clearance for the top edge of the door. f ........... ocH,) Door clearance brackets are available for sectional doors when headroom clearance is _essthan 2°_See accessory page 38 Sectiona! door One,_p_ece door wtth curved track with horizontal track Proceed to Step 2_ page 14o 12 Read the Safety instructions on page 12. They also apply to doors without tracks. ,Ciose #_e d_r and ma_'kthe inside veRicai centerline of your garage door. E_end the line onto the header wall above door tf headr_m c{earance {s minimal, you can instai_ the header bracket on the ceiling. See page 14. header bMcket on a 2x4 (on wall or ceiling), use lag _rews (not suppti_) to secure_J fasten the 2x# to structural On.piece door without track One-pi_e door without track pivot hardware , Open your door to the highest _int of trave_ as EXAMPLE shown Measure the distance from the top d the Distance from top of door door to the floor° Subtract t,he actual height d the (at highest point of travel) to fk_r .................... 92" door. Add 8_to the remainder. (See Example). Actua_ height of dc@r ............................................ 88" -Close the door and draw an inte_ectJng horizontal Remainder .................................................................. line on the header w_l at the dete_ined height.. Add ......................................................................... if the total number of inches exceeds the height Bracket height on header wali .............................. =12" available in your garage, use the maximum height possible, or refer to page 14 for ceiling (Measure UP from top of CLOSED door.) ins_llatfon. Proceed to Step 2, page 14. 13 Youcanat_ch theheaderbracketeithertothe wail above the garage door, or to the ceiling. Follow the tnstr_Jctions which will work _st for your pa_leuJar requirements. Fasten the Header Bracket to the Wall o Center the bracket on the veAical guideline with * Mark either set of bracket holes (do not use _e the bo_om edge of the bracket on the hodzonta[ holes designated for ce#ing mount), Ddl{ _16" pilot tine as shown (with the arrow pointing toward the holes and fasten the bracket securely to a stm_u_ suppo_ with the hardware provided. W_ Hardware Shown Actua_ S_ze Fasten the Header Bracket to the Ceiling , Extend the ve_icat guide{ine onto the ceiling as shown, -Center the bracket on the ve_ica_ maP_ no more than 6" from the wall, Make sure the arrew is pointing toward the wall The bracket can be mounted flush against the ceiling when clearance is minima_ Mark h@es designated for ceiling mount only Drill 3/16 _pilot holes and fasten bracket securely to a stru_ura_ suppo_ with the hardware pro,tided r_i_g M_r_Sng Ho_es The n_ how is for _'6_n 9 ®_y, Yo,J must _se _ag _r_s lo _T_un_ _h@header b_'_ck_{ 14 installation Step Attach the Torafl to the 3 Header Bracket o Position the o_ner on the garage fl_r below the header bracket, Use packing material as a If the door spring Is in the way you'l! need help, Have someone hold the opener securely on a tem_ra_ suppoA to allow the T-rail to clear the oPosition bracket the _b_e puiley bracket against the header Align the bracket holes and ioin with a clevis p_n as shewn, hse_ a r_ngfastener to secure, Hardware Shown Actual Size O Clevis P_ 15 Installation Step 4 Position the Opener Folow instructions wMch apply to your door type as l_ustrated. A 2.4 [aid fiat is convenient for setting an ideal door4o-T-ra/distance° Raise the opener onto a stepladder, You will ne_ help at this point it the ladder _a +Open the door a/the way and place a 2.4 _aidflat on the top section beneath the T-ra/ If the top panel hits the trolley when you raise the door, puff down on the troltey release arm lo disconnect the inner and outer sections. The trolley can remain disconnected until S_ep 12 is With the door fu/y open and paratel to the floor, measure the distance from the floor to the top of the door Using a stepladder as a sup_)., raise the opener to the same distance as the d_r from the floor (it will be at a stght angle as shown). The top of the door should be level with the top of the opener Do not position the opener more than 2'_above this point installation Step 5 Hang the Opener Two represen_gve installations are showo. Yours may be different, Hanging brackets should be &qgted, Figure 1, to provide rigid support On finished ceilings, Figure 2, a_ach a sturdy metat bracket to st_Jctural supports before installing the opener. The bracket and fastening hardware are not supplied. See accessory page 38. Measure the distance from each side of the opener to the strdctura! support° Cut both pieces of the hanging bracket to requ red DdH3/16" pilot h@es in the structu...
Otros modelos de este manual:La puerta automática - 139.53225SRT (7.32 mb)
La puerta automática - 139.53325SRT (7.32 mb)
La puerta automática - 139.53628SRT (7.32 mb)
La puerta automática - 139.53629SRT (7.32 mb)