Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The light will turn ON and remain lit for approximately 4q/2 minutes when _wer is connected. Then the light will turn OFF. , If the bulb bums out prematurely due to vibration, replace it with a standard neck "Garage Door Ught Install the lens (except for Modef 53225) Apply slight pressure on IJsesides of the _ens and slide _e tabs into the slots in the end p_ef , Reverse the procedure to remove the fens° lnstalJation Step 8 Attach the Emergency Release Do not use the red handle to pull the door open or closed, The rope knot couid become untied and you could Carl. Use the emergency release only to d_sengage the trolley and:, if possible, only when the door ts etosed. Garage doors are heavy. If the door is open when the handle is pulled, the door could close inadvertently if ft is not properly balanced, Sedous injury may result to persons under the door, Make sure the doorway ts clear of persons and obstructions before pulling handle when door is open, -Thread one end of the rope through the hole in the top of the red handle so "NOTICE" reads dght side up as shown Secure with an overh_d keel R®e The knot should be at least 1" from the end of the rope to prevent slipping, , Thread the other end of the rope through the hole in the release arm of the outer trolley * Adjust rope length so the handie is 6 feet above the floor. Secure with an overhand knoL If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling. t9 t ins aliat on Step 9 Electrical Requirements j "Toreduce the dsk of eleetdc shock, your garage door opener has a grounding type plug with a third grounding pin. This pbg will only fit into a grounding If the plug doesnt fit into the outlet you have, conta_ a qu_ifi_d el6_Cia_ to install the pro_r outlet. "Toavoid inataflatlOn difficulties, do not run the opener at this time, { ] If permanent wiring is required by your local code, refer to the following procedure: To prevent eiectrocufion, remove power from the garage door opener and from the circuit you plan to use for the permanent connection, To make a permanent oannection through the 718_diameter hole in the top of the opener (according to I_l code): Remove the opener cover screws and set the cover aside_ Remove the attached 3 prong cord , Connect the black (line) wire to the screw on the b_ass terminal;: the white (neutral) wire to the screw on the shyer terminal7 and td-_eground wire to the green ground screw. The opener must be o Reinstall the cover. To avoid insfatlation dtfficutties_ do not run the opener at this time. 2O Safety Reversing System Information you1] need before you begin the The safety reversing sensor must _ connected and aligned correctly before the garage door opener wlil move in the down direction. This is a required _fety device and cannot be disabled, Instalia#on pr_edures are the same for sedionat Be sure po'#er to the opener is disconnected. The sending eye transmits an invisible tight _am to the receiving eye The units can be installed on eider side of the garage door as long as the sun never shines directly into the receiving eye lens, Lc_k at the label on the eonneGor end of each use to identiPy the sensors. The brackets must be connected and fastened so that the sending and receiving eyes face each other as shown in Figure I. If an obstruct on breaks the light beam while the garage door is c_osing_ the door wilt stop and reverse to fuil open position and the opener lights will flash for 5 seconds installation of the safety reversing sensor. Without a properly working safety reversing sensor, persona (particularly children) could be in]u_ or killed by a closing garage door. Read and follow all instructions. To protect small children, Install the safety reversing sensor so that the beam wi[[ be no higher than 4"4" above the garage fi_ro Disconnect power to the garage door opener before installing the safety reversing sensor. The bracket_ must be securely fastened to a solid sudar_ such as the studs on either side of the door, or add a piece of wood at each location if installing in The invisible Hght beam path must be unobstnJcted. No pad of ttie garage door (or door tracks, spdngs, hinges_ roIIers or other hardware} can interrupt the beam whiie the d_3r is closing If it does, use a pie_ of wr_d te build out each sensor mounting iocation to the minimum depth required for Ight beam c_earance a_3ve f;c_ f_rot_::_n Area Figure 1 : Facing the door from inside the garage 21 Figures2and3 showassemblyofbracke_and °C" wrap based on the recommended instafiation of the sensors as shown on page 21 However, Figures 4 and 5 are variations which may ins_i_ation requirements baser Make sure the wraps and brackets are align_ so the sensors will face each other across _e garage door, Fasten the "C_ wraps to the mounting brackets having square holes, using the hardware shown n Figure 2 Connect each assembly to a slo_ed bracket, using the hardware shown in Figure 3_ Note the alignment of the b...
Otros modelos de este manual:La puerta automática - 139.53225SRT (7.32 mb)
La puerta automática - 139.53325SRT (7.32 mb)
La puerta automática - 139.53425SRT (7.32 mb)
La puerta automática - 139.53629SRT (7.32 mb)