Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
CONT2 ENTS Wireless Keyless Entry Installation..... 20 Features……………….. 4 Opening & Closing Force Adjustment… 21 Door Tests……….......... 5 Contact Obstruction Sensing Adjustment. 22 Pre-Assembly Check…………. 5 Mechanical lock Adjustment......... 22 Installation Instructions………… 6 Operational Safety Rules……… 23 Installing Wall Station……….… 8 Operation on Your Opener………. 24 Install Infrared Safety Sensors……. 9 Emergency Release Disconnect...... 26 Wall Station Code Change Maintenance Schedule………... 27 and Programming…………. 14 Trouble Shooting…………… 28 Infrared Safety Sensors Alignment 16 Parts Breakdown-Rail Assembly…… 29 Transmitter Code Change & Programming 16 Parts Breakdown-Power Head Assembly. 30 Travel Adjustment…………… 19 Accessories……………... 31 Obstruction Sensing Test……... 18 Warranty.……………..... 32 Infrared Safety Sensor Obstruction Test. 19 © Copyright 2003 Wayne-Dalton Corp. Part No: 307545 New 6/18/2003 Read These Important Safety Rules Before Proceeding This symbol indicates caution and appears throughout this instruction manual. This garage door opener is designed and tested to offer reasonably safe operation if installation is followed in strict accordance with these safety instructions. Failure to comply with these instructions may result in serious personal injury or property damage. IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. Install only on a properly balanced garage door. An improperly balanced door could cause severe injury. Have a qualified service person make repairs to cables, spring assemblies and other hardware before installing opener. To reduce the risk of injury to persons, use this operator only with sectional overhead doors. Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your garage door manufacturer for their recommendations. Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener. Do not use sensitivity adjustments to compensate for a poorly operating door. This will interfere with the proper operation of the safety reverse mechanism and may damage the door. Locate control button: within sight of door, at a minimum height of 5 feet, so small children cannot reach it, and away from all moving parts of the door. If possible, install door opener 7 feet or more above floor. Mount the emergency release knob 6 feet above the floor. Do not connect opener to source of power until instructed to do so. Installation and wiring must comply with local building and electrical codes. Connect the power cord to a properly grounded outlet. Do not remove round ground pin from power cord. Install entrapment warning label next to control button in a prominent location, such as the inside of the garage door, or as instructed in the installation instructions. If label adhesive will not adhere to the surface, secure the label by additional mechanical means such as staples, nails or screws. If necessary, use an intermediate mounting surface, such as plywood, cut to the appropriate size. Install Emergency Release tag to the emergency red cord. After installing opener, the door must reverse when it contacts a 1 inch high solid test object on the floor. Open door must not close and closing door must open if photoelectric system in obstructed by 6” x 12” object, using test procedure described in Step 30. Do not wear rings, watches or loose clothing when installing or servicing a garage door system. Use a sturdy, non-metallic step ladder. AFTER INSTALLATION IS COMPLETE, FASTEN THIS MANUAL NEAR GARAGE DOOR. PERFORM PERIODIC SAFETY CHECKS, MAINTENANCE AND ADJUSTMENTS, AS RECOMMENDED. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by Wayne-Dalton Corp. could void the user’s authority to operate the equipment. FCC Regulatory Information: This device...
Otros modelos de este manual:La puerta automática - 3414 (720.73 kb)
La puerta automática - 3314 (720.73 kb)
La puerta automática - 3316 (720.73 kb)