GRANT ACCESS0-9, A-Z SCROLL BLOCK USERDELETE USERENTERADD USERDEVICE SETUP RELAY OUTPUTN.O. contacts SERIAL PORT VOLTSELECT ACRx 2MODEL 1025LM KEEP TERMINALS COVEREDHAZARDOUS VOLTAGES! 24VAC 12/24VOLTSAC/DC EXT. GRANTSWITCH exit TM ACRx 2 Model 1025 OWNERS MANUAL WARNING WARNINGWARNING Disconnect power to the garage door or gate opener before installing the receiver. Children operating or playing with a garage door or gate opener can injure themselves and others. The garage door or gate could cl

¦ The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned. ¦ Periodic checks of the opener are required to ensure safe operation. ¦ The model number label is located on the back of your opener. Contents Safety alert symbol review ...........................................2 Install the lights and lens ..........................................19 Safety information and precautions ..............................3 Attach the manual release rope and handle.............

¦ The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned ¦ Periodic checks and adjustment of the opener are required to ensure safe operation. ¦ The model number label is located under the light lens on the left side of your opener. CONTENTS PAGE CONTENTS PAGE A review of safety alert symbols ...............................2 Electrical connections ...........................................16 You'll need tools.......................................................

• Remove the attached 3-prong cord. • Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded. • Reinstall the cover. To prevent electrocution or fire, installation and wiring must be electrical and building To avoid installation difficulties, do not run the opener at this time To avoid installation difficulties, do not run the opener at this time • D

30, 31 Safety warnings.......................................................................................................................25, 27 Door hardware.......................................................................................................................Maintenance ...............................................................................................................................7, 24-27 Reinforcement requirements .............................................

The hazard may come from something mechanical or from electric shock. Read the instructions carefully. Mechanical Electrical When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the corresponding instructions. Read the instructions carefully. This garage door opener is designed and tested to offer safe service provided it is installed, operated, maintained and tested in s

Assembly Step 2 Attach Chain to Sprocket and Install Sprocket Cover For Models 1260, 1260-266, 1255,1255-266, 1250, 1250-266, 1245, 1245-266 and 1240 • Position chain over the opener sprocket. If necessary, loosen the outer nut on the trolley to obtain more chain slack. • Insert the second washered screw. CAUTION: Use only the screw previously removed from opener! • Tighten both screws securely through the T-rail into the opener as shown. Install the sprocket cover: • Insert the back tab in the

ASSEMBLY STEP 1 Attach the T-Rail to the Motor Unit To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered screws mounted in top of motor unit. • Position T-rail at a 45° angle to opener so one hole in T-rail and motor unit line up. • Thread one of the washered screws part way in. Use only these screws! Use of any other screws will cause serious damage to door opener. • Align T-rail and styrofoam over sprocket. Cut tape from T-r

(NOT PROVIDED) Door Bracket Vertical Centerline UP Vertical Reinforcement Self-Threading Screw 1/4"-14x5/8" Door Bracket Nut 5/16"-18 Bolt 5/16"-18x2" Lock Washer 5/16" Vertical Centerline UP Vertical Reinforcement Figure 2B UP Vertical Centerline Self-Threading Screw 1/4"-14x5/8" Figure 3 UP Inside Edge of Door or Reinforcement Board Bolt 5/16"x2" Vertical Centerline Figure 4 Self-Threading Screw 1/4"-14x5/8" HARDWARE SHOWN ACTUAL SIZE 20 ONE-PIECE DOORS Please read and comply with the warnings

If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on page 7. 3. Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restriction. 4. The garage door spring may be broken. Have it replaced. 5. Repeated operation may have tripped the overload protector in the motor. Wait 15 minutes. Try again. Opener operates from