Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
• Decide on a suitable location for the equipment rack that will hold the RSS 2000 unit and is near a grounded power outlet. • Use a regulating uninterruptible power supply (UPS) to protect the RSS 2000 unit from power surges and voltage spikes, and to keep it operating in case of a power failure. Table 1 Hardware Specification Parameter Description Hardware Capability Pentium 4, 2.8Mhz, 2G RAM, 250G Hardisk. Form Factor 1U 19” rack mount Height 1.73” (44 mm) Width 16.83” (430 mm) Depth 15.35” (390 mm) Gross Weight 22.4 lbs (10.2 kg) Power Supply Thermal controlled 220W ATX AC power supply w/PFC AC Voltage 100 - 240 VAC, 60-50 Hz, 5-3 Amps Operation System Windows XPEK OS First Time Installation and Configuration Preparations Obtain the following information from your network administrator: • RSS 2000 unit, Subnet Mask and Default Gateway IP addresses • Gatekeeper IP address, Prefix, and E.164 of the RSS 2000. Unpacking and Installing the RSS 2000 1 Place the RSS 2000 unit on a stable flat surface in the selected location. 2 To connect to the power source, insert the power cable into the Power connector on the rear panel of the MGC+ unit and insert the Power cable into the power source socket. 3 Connect the LAN cable to LAN1 in the back of the system. 4 Turn on the power switch. Initial RSS 2000 IP Configuration The system is shipped with a default IP configuration: IP Address:192.168.1.254 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 There are two ways to change the initial IP address of the sytem: • Via a cross over LAN cable • Via a RS232 or Telnet Console. Changing the initial IP address via a cross over LAN cable 1 Connect a cross over LAN cable to LAN1 in the RSS 2000. 2 Set your laptop to the same segment of the RSS For example (in your laptop IP config setting): First Time Installation and Configuration 3 Open a browser and go to: 4 Login to the system. User name: administrator Password: polycom 5 Go to system configuration->IP setting and modify the IP address. You can set a static IP or choose DHCP. Click the save button and then reset the system. Changing the initial IP address via an RS232 Console or Telnet Another option to modify the IP address of the RSS 2000 is using the RS232 console. Connect to the RS232 port – and activate the console (9600, 8bits) Login: polycom (or any administrator password) When you first login to the console, you will see the current IP address of the system. Help # ? – show all available commands Changing the IP Address # set lan1 static 172.21.100.20 mask 255.255.224.0 [gw 172.21.96.254] Reset Password (back to polycom) A user may reset the password of the administrator to the default of ‘polycom’ # reset password First Time Installation and Configuration • The same process applies also for Telnet connections. • Only one console session can be active at any given time (either Telnet or RS232, not both). The system is now ready for use. For additional configuration instructions, refer to the user guide. RSS 2000 Maximum Capacity Table 2 Maximum Capacity Scenario Description Maximum Capacity Conference Recording How many conferences can be recorded simultaneously? 2 conference recording links, or 2 endpoints dialing in the same time. Only 1 recording session at a time may utilize H.239. Point to Point recording How many point to point calls can be recorded (if both are dialing into the POLYCOM ™ RSS 2000)? 1 point to point call can be recorded, as the two connections to the recording room utilize both available ports on the RSS 2000. H323 Playback How many recordings can be simultaneously played back in H323? 10 recordings. This includes playback from the local RSS 2000, or from other units in a clustering group. Archive playback (WMV Unicast) How many streams/archives can be simultaneously viewed (unicast)? 50 streams/archives. This is based on the Web Server’s capacity. Archive playback (Multicast) How many streams/archives can be simultaneously viewed (multicast)? 2 streams can be viewed using the RSS 2000 Multicast Viewer. The archives must be enabled for multicast streaming. See the User Guide for details. Clustering How many RSS 2000 devices can be clustered in a single group? There is no limitation for the amount of RSS 2000 devices that can be in a single clustering group. 1. In clustering mode, each RSS 2000 still supports 10 H.323 playback sessions. For example: One H.323 endpoint connects to RSS-A to playback an archive residing on RSS-B (B is in a clustering group with A in this example). The H.323 playback resource it occupies is taken from RSS-A, even though the archive resides on RSS-B. RSS-A has 9 additional H.323 playback sessions available, while RSS-B still has all 10 sessions available. 2. WMV playback via the archive list in the web UI of a clustered RSS 2000 will utilize unicast streaming resources from the RSS device where the archive actually resides, not from the clustered device that the user is connected to. Note thi...