Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
O P E R A T I O N 3 Fold open this manual for information about this product’s installation and operation. Please read Part 1 – Important Product Information, included in this package. User’s Manual for Tapeless Digital Answering System with Time/Day 1717 1 Part 2 © 1998 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico. 848230009 Issue 3AT&T REVISED 1/15/99 AT&T 1717 panels_3ATT 1 1/15/99, 1:40 PM OPERATION Announcement Monitor Saving Messages You can choose whether to hear the The system automatically saves your announcement when your system answers messages if you do not delete them. The a call, or have it silent (off) on your end system can save about 12 minutes of (your caller will still hear an messages, including your announcement, announcement). for a total of up to 59 messages. When 1 Press and hold S . After the Ring memory is full, you must delete some or Select setting is announced, continue all messages before new messages can be to press and release S until the recorded. system announces “ Monitor is on (or off) ” . Deleting Messages 2 Press and release Delete all messages — Hold down or D . The system announces “ Messages until the system announces your deleted” and permanently deletes selection. messages. The Message Window displays 3 Press and release P or S 0. If you haven’t listened to all of the to exit. messages, the system beeps five times, and does not delete messages. Listening to Your Messages Delete selected messages — Press and As the system plays back messages, the release D while the message you Message Window displays the number of want to delete is being played. The system the message playing. Before playing each beeps once, and continues with the next message, the system announces the day message. If you want to check a message and time the message was received. After before you delete it, you can press playing the last message, the system to replay the message before deleting it. announces “ End of messages.” Play all messages — Press and release When the system reaches the end of the P . If you have no messages, the last message, the messages not deleted are system announces “ No messages.” renumbered, and the Message Window Play new messages only — Hold down displays the total number of messages P for about two seconds, until the remaining in memory. system begins playing. If you have no new messages, the system announces “ No new Recording a Memo messages.” You can record a memo to be stored as an Repeat entire message — Press and incoming message. The memo can be up release . to three minutes long, and will be played Repeat part of message — Hold downback with other messages. for a few seconds, then release 1 Press and hold . After the it to resume playing. The system beeps beep, speak toward the microphone. while the button is held down. 2 To stop recording, release . Repeat previous message — Press 3 To play the memo, press P . twice, continue this process to hear other previous messages. When Memory is Full Skip to next message — Press and The system can record approximately release . 12 minutes of messages, including your Skip part of a message — Hold downannouncement, for a total of up to 59 for a few seconds, then release it messages. When memory is full, or 59 to resume playing. The system beeps messages have been recorded, the while the button is held down. Message Window flashes F. Delete Stop message playback — Press and messages to make room for new ones. release P . When memory is full, the system answers calls after 10 rings, and sounds two beeps instead of your announcement. 4 AT&T 1717 panels_3ATT 2 REMOTE OPERATION Connect with the Deleting Messages Answering System Delete All Messages After you have listened to all messages and 1 Dial your telephone number from a heard the two beeps, press 33 . touch tone phone with a different telephone number. Delete Selected Messages 2 When the system answers, enter your Press and release 3 while the message you three-digit Access Code during or want to delete is playing. after the announcement. The system announces the number of messages, Record Announcement then beeps twice. If you don’t 1 Press 7* , and begin speaking after hear the two beeps, wait for the the beep. announcement to end or press # to 2 Press 5 when you are finished. The stop the announcement, then re-enter system replays your new announcement. the code. 3 The two-beep signal lets you know To review your announcement — Press the system is ready to accept a remote 71 . command. Record a Memo Playing Messages 1 Press # and begin speaking after the 1 After the two beeps, wait four seconds, beep. and the system plays back messages 2 Press 5 when you are finished. — OR — Room Monitor with Intercom Press and release 1 to play all messages You can call the answering system and — OR — listen to any activity in the room. Press and release 2 to play only new 1 Press 98 to listen for 30 seconds. messages, the system announces “ N...