Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
The unit immediately stops recording and returns to Idle mode. Because the recorded portion of the message is kept, the new call and message counters increase by one and the message indicator flashes. READING THE MESSAGE COUNTER The total number of incoming memos and messages is shown in the display. When the maximum number has been reached, the unit begins erasing messages, starting with the first message recorded. LISTENING TO MESSAGES The unit plays memos before messages. If there are no new memos, the unit starts playing new messages. If there are no new memos or new messages, the unit announces "you have no new messages" and plays all old memos before playing all old messages. If there are no old memos, the unit plays all old messages. Tap the PLAY button to hear memos and/or messages. At the end of each memo or message, the unit states the time and date each memo or message was recorded. After all memos and messages have been played, the unit announces "end of messages." The unit then prompts you to "press delete to erase msgs." See "Deleting" on Page 14. If you listen to all your memos and messages, the message indicator stops flashing. PAUSING DURING PLAYBACK 1. Press the PAUSE button during playback to suspend activity. 2. Press the PAUSE button again to resume activity. • If a button other than the PAUSE button is pressed, the unit resumes playing the message. • If still in Pause mode after 10 seconds, the unit automatically resets to the Idle mode. REVIEWING AND SKIPPING Tap the REVIEW ( ) button to repeat the same memo or message. Pressthe button to reverse to previous memos, messages or caller ID entries. Tap the SKIP ( ) button to advance to the next memo, message or caller ID entry. DELETING To delete the voice part of a memo or message but not the caller ID information, tapthe DELETE button during playback. To delete both voice and caller ID information of the current memo or message, pressthe DELETE button during playback. The unit announces "message erased" for confirmation. To delete all voice memos and messages, wait for the unit to announce "end of messages." Pressthe DELETE button within 8 seconds of the prompt "press delete to erase msgs." To delete both voice and caller ID information or caller ID information if there is no voice message - of all memos and messages, hold the DELETE button within 8 seconds of the prompt. The unit announces "all messages erased" for confirmation. RECORDING A MEMO 1. Holdthe MEMO button. 2. Begin speaking after the beep. There is no limit on the recording time. NOTE: If you speak directly into the microphone your announcement will be clearer. 3. Release the MEMO button when you have finished speaking. The message counter increases by one and the message indicator flashes slowly. • While the unit is receiving caller ID information, you cannot access the Memo mode. MEMORY FULL When the unit's memory is full, it picks up after 10 rings. After a two-second delay, it emits three beeps. A 20-second waiting period follows, allowing the caller to enter your security/user code. REMOTE ACCESS To enter Remote Access mode during or after the announcement, press the # button and then enter the correct security/user code. The unit emits another tone while it waits for you to enter one of 10 function commands. See Page 16 for commands. After each function is performed, the unit emits the same tone. If no command is entered after 20 seconds, the unit disconnects the line and returns to the Idle mode. • The unit allows two attempts at entering the correct security/user code. If, after the second try, the security/user code is not correct, the unit disconnects the line and returns to the Idle mode. To end the remote operation, hang up or press 3 on the phone for the Hang Up code. Remember that when you play your messages by remote access, the Toll Saver feature resets the unit to answer on the 5th ring. DISABLING REMOTE ACCESS To disable remote access, set your security/ user code to 000. This also disables remote turn on and the ability to erase messages in the event the unit's memory becomes full. Write 3-digit security code in boxes. Digital Messaging System 2-9991 1. Dial phone number of the answerer. 2. Press the # key to enter the Remote Access mode. 3. Enter 3-digit security code. 4. Enter touch-tone command. 5. Hang up. Write 3-digit security code in boxes. Digital Messaging System 2-9991 1. Dial phone number of the answerer. 2. Press the # key to enter the Remote Access mode. 3. Enter 3-digit security code. 4. Enter touch-tone command. 5. Hang up. (during message playback) (during message playback) To: Press: Play menu Hang up Play previous message Repeat current message Skip to next message Record new announcement Turn answerer on or off Change announcement Delete memo/message Play/pause messages (during message playback) 0 CALLER ID Caller ID information is retrieved between the first and second ring. In the display, the unit shows the number of calls, the cal...
Otros modelos de este manual:Respuestas Automáticas - 15298530 (190.96 kb)