Votos - 5, Puntuación media: 3.2
(
)
)
|
Resumen del manual
Telephone Line Cable 2. Ans / Annc Only Switch 3. Call Back Button 4. Display 5. Erase Button 6. Microphone 7. Volume Button 8. / OGM Button 9. Play / Pause Button 10. Menu Button 11. Delete Button REPEATMEMONEWCALL# MENU PAUSE PLAY STOP MEMO/2 WAY DELETE OGM TIME CHECK ON/OFF REVIEW CALL BACK ERASE ANSWERING SYSTEM AM880 12 13 14 15 16 17 18 19 20 21 22 12. 2 / 6 / TS Switch 13. Power Jack 14. Telephone Line Socket 15. New Call LED 16. Review / Button 17. Speaker 18. Message LED 19. / Time Check Button 20. Memo / 2 Way Button 21. On / Off / Stop Button 22. Volume Button N13134 The A-Tick symbol indicates that this product complies with all current Australian ACA standards. 1 2 Installing your Oricom AM880 2.1 Installing the optional backup battery (not included) Before connecting your AM880 to the telephone network, the battery should be fitted. Always use a new 9V alkaline block-type battery. The battery is required for preventing loss data if there should be a mains power failure. Note: When icon appears in the display, the battery needs to be changed. 1. Make sure that the answering machine is not connected to the telephone network. 2. The battery compartment is to be found on the underside of your answering machine. 3. Open the battery compartment with a small screwdriver. 4. Connect the battery plug to the battery and place these in the battery compartment. 5. Close the battery compartment. 2.2 Connecting the telephone line 1. Connect the small plug of the telephone line supplied to the TEL.LINE socket on the rear of the answering machine. 2. Plug the other end of the cable into your telephone wall socket. 2.3 Connecting mains (AC) power adaptor CAUTION Use only the mains adaptor supplied with this product. Incorrect adapter polarity or voltage can seriously damage the AM880. Adaptor Model #: 9VDC300, Input: 240 VAC 50 Hz, Output: 9VDC 300mA 1. Plug the AC adaptor into mains power. 2. Plug the small plug end into the power socket on the rear of the answering machine. When powering up for the first time, your AM880 will need approx. 20 seconds to initialise all the functions. After the first initialisation, the display will show LCD CONTRAST. 2 Setting up your AM880 Before you start using the AM880, you need to adjust basic settings such as the date and time. When the adaptor has been connected, the display will show LCD CONTRAST. If LCD CONTRAST doesn’t appear, please adjust the contrast. First press and hold the MENU button for approx. 3 seconds this will allow you to adjust the following 1. Press CALL BACK button to confirm the LCD CONTRAST. The current contrast level will be displayed. 2. Now you can use REVIEW or button to set the contrast level. 3. Press CALL BACK button. ENTER WEEK appears on the display. 4. Press CALL BACK button. The display will show SUNDAY and the AM880 announces the weekday. 5. Press REVIEW or button to set the correct weekday. 6. Press CALL BACK button, the AM880 announces the weekday set and the display then shows ENTER TIME. 7. Press CALL BACK button.The hour digits will blink and the AM880 announces the hour. 8. Press REVIEW or button to set the correct hour. 9. Press CALL BACK button, the minute digits will blink and the AM880 announces the minute. 10. Press the REVIEW or button to set the correct minute. 11. Press CALL BACK button to confirm. The AM880 announces the time set and the display then shows ENTER DATE. 12. Press CALL BACK button. The month digits will blink. 13. Press REVIEW or button to set the correct month. 14. Press CALL BACK button, the day digits will blink. 15. Press REVIEW or button to set the correct day, then Press CALL BACK button to confirm. This procedure has now been completed - you should see all the current data you entered on the display. NOTE: • Press the ERASE button to exit a menu at any time. • To check the time and date, just press the / TIME CHECK button. The AM880 will announce the current time. • If there is a delay of 30 seconds between any of the steps, the AM880 will revert to standby mode. 3 3.1 Turning the AM880 ON and OFF To turn on the AM880, press ON/OFF/STOP button. The PLAY LED illuminates and the AM880 is ready to answer calls. To turn it off, press ON/OFF/STOP button. The play LED turns off. 3.2 Recording outgoing messages (OGM) The AM880 has two prerecorded outgoing messages: 1. An outgoing message that says ‘Hello, please leave a message after the tone’. If the ANS/ANNC ONLY switch is set to ANS, the AM880 will play this message to your callers unless you record your own. 2. Announce-only outgoing message that says “No one is available to take your call”. If the ANS/ANNC ONLY switch is set to ANNC ONLY, the AM880 will play this message to your callers unless you record your own. To record your own OGM (up to 5 minutes in length): 1. To record an outgoing message, slide ANSN/ANNC ONLY switch to ANS. To record an announce-only outgoing message, slide ANS/ANNC ONLY switch to ANNC ONLY. 2. Press and hold / OGM button and t...
Otros modelos de este manual:Respuestas Automáticas - AM880 (108.4 kb)