Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
16 General Information General Information WARNING It is very important that you read the User Guide carefully as it contains detailed information on setup and operational issues which you will need to be aware of to ensure this product operates properly. Following is a list of some of the important issues and important warnings which you need to be aware of. •Theproductisdesignedforindooruseonly.Donotinstall in areas where there is the risk of an explosion, excessive exposure to smoke, dust, vibrations, chemicals, moisture and heat. •Donotusethisproductduringathunderstormasit is possible to get a shock. Refer to information contained in Telstra White pages directory. •Thisproducthasbeendesignedforindividualswhoare hard of hearing and has a normal playback volume which is louder than a standard product. Use of the boost button feature could cause hearing damage to individuals who are not experiencing hearing loss. • Donotinstallindamplocationssuchasabathroomor laundry, do not expose the unit to direct sunlight. •DonotconnectthisproducttoanextensionofaDigitalTelephonesystem(PBX).Damagetothisproduct or the phone system may occur. General Information Notes for operation in New Zealand The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. Telepermitted equipment only may be connected to the auxiliary telephone port. The auxiliary telephone port is not specifically designed for 3-wire-connected equipment, 3-wire-connected equipment might not respond to incoming ringing when attached to this port. REN (RN for New Zealand) The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1 telephone to your telephone line. A standard telephone line has a maximum REN capacity of 5 (RN of 5). It is possible to connect 5 devices with a REN of 1 (RN of 1) with no degradation to the product’s performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all. 4 Location of controls Location of controls 1 2 3 4 13 12 15 14 5 21 16 17 18 19 20 6 7 8 9 1011 Location of controls 1. Message LED 2. Microphone 3. PLAY SPEED Switch 4. REPEAT button 5. REC button 6. ON/OFF button 7. DOWN VOLUME button 8. PLAY/PAUSE button 9. DELETE button 10. BOOST button 11. BOOST Led 12. SKIP button 13. TONE switch 14. UP VOLUME button 15. Speaker 16. Telephone Line Socket 17. Ringer 2/6/TS Switch 18. ANS/ANS ONLY switch 19. Headset socket (for headset not supplied) 20. Socket for AC Adaptor 21. Integrated Line cord N13134 The A-Tick symbol indicates that this product complies with all current Australian ACMA standards. PACK CONTENTS 1 A900 Answering System 1 Energy efficient AC Adaptor 1 Australian Modular Adaptor Plug Getting Started Connecting your Oricom AM900 Example of Connecting the System Connect to a phone wall socket. Adaptorplug(supplied) Modular line cord not supplied. Existing corded or cordlessphone(notsupplied) Depending on the type of phone and phone wall socket you have you may need to purchase a different type of telephone line adaptor plug. These are available from electronics stores. Warning. Use only the AC adaptor supplied with this product. Incorrect adaptor polarity or voltage can seriously damage the AM900 and or be dangerous. AC adaptor part number #: S005CS0900030, Input: 100-240V, 50/60 Hz, Output: DC9V 300mA 1. Plug the AC adaptor into a power point. 2. Plug the small plug on the AC adaptor into the socket on the rear of the answering system. 3. After initialisation, the display will show 00 on the message counter. Setting the day, time and Language The answering system always saves the day of the week and the time of day with each recorded message so that you always know when callers left their messages however the time and day must be set correctly. If you want to enter the day, time and language for the first time or if you want to change a day and time that has already been set, please proceed as follows: 1. Press and hold the SKIP button for 2 seconds. You will hear the day of the week. 2. Press the SKIP button repeatedly until you hear the correct day of the week. Getting Started 3. Press the REPEAT button. You will hear an announcement of the hour. 4. Press the SKIP button repeatedly until you hear the correct hour announced. 5. Press the REPEAT button. You will hear an announcement of the minutes currently set. 6. Press the SKIP button repeatedly until you hear the correct minutes announced. 7. Confirm with the REPEAT button and the day and time announcement will...
Otros modelos de este manual:Respuestas Automáticas - AMPLIFIED DIGITAL ANSWERING SYSTEM AM900 (457.43 kb)