Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
NOTE: Many phones take up to 20 seconds to reset the bar indicator. To maximize performance, attach the universal connector as close as possible Figure 1 Figure 2 To Amplifier Powering up the Amplifier Make sure both the outside antenna and universal connector cables are connected before powering up the amplifi er. For vehicle use, connect the power cable from the DC power supply to the amplifier input marked “Power” and insert the large end into DC power socket (the cigarette lighter outlet). For home or office use, connect the cable from the AC/DC power supply (sold separately) to the amplifier input marked “Power” and insert the plug end into a standard wall outlet. Warning: Use only Wilson power supply units. Use of a non-Wilson product may damage your equipment. !12 V DC power supply (included) The amplifier may remain on all the time. However, leaving the amplifier on in a vehicle when it is not running can discharge the battery in a day or two. A good option is to power the amplifier through the ignition switch so the amplifier is turned on and off with the vehicle. IMPORTANT: Do not power up the amplifier unless the antenna and universal connector cables are attached to the AC/DC power supply (not included) amplifi er. NOTE: The aluminum casing of the SIGNALBOOST™ amplifier will adjust very quickly to the ambient temperature of its environment. For example, in the summer, when the inside location with adequate ventilation, such as under the seat or dashboard. Keep the area free of items that could block air flow to the amplifi er. 8of a car can reach 140 degrees Fahrenheit, the amplifier temperature may be 150 degrees or higher. The casing will be hot to the touch, similar to a metal door handle or steering wheel. Such high temperatures will not damage the amplifier, nor do they pose a fi re risk. As recommended in these instructions, when installing the amplifier in a vehicle, select a Warning: Do not plug the amplifier directly into the cell phone or cellular data card using an antenna adapter. It will damage the cell phone or cellular data card. Warning: Do not plug in the power supply until the antenna and universal connector cables are attached to the amplifier. Warning: The antenna must be installed with a separation of at least 11 inches from nearby persons and must not be located or operating in conjunction with any other antenna or amplifier. Use of this amplifier with an antenna gain higher than 6.12 dBi is in violation of FCC regulations for which the offender is fully liable. All Wilson mobile antennas are 6.12 dBi or less. Warnings and Recommendations Recommended amplifier installation locations for a vehicle are: • Under the seat • Under the dash Power the amplifier through the ignition switch so the amplifier is turned on and off with the vehicle. Recommended amplifier installation locations for a home or office are: • On a desk or table top • In a bookshelf • On the floor 99 About Wilson Electronics Wilson Electronics, Inc. has been a leader in the wireless communications industry for nearly 40 years. The company designs and manufactures amplifiers, antennas and related components that significantly improve cellular telephone signal reception and transmission in a wide variety of applications, both mobile and in-building. With extensive experience in antenna and amplifier research and design, the company’s engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fine-tune antenna designs and performance. For its amplifiers, Wilson uses a double electrically insulated RF enclosure and cell site simulators for compliance testing. All products are engineered and assembled in the company’s 50,000-square-foot headquarters in St. George, Utah. Wilson has product dealers in all 50 states as well as Canada and Mexico, Central and South America. 10INCREASEYOURBARS Amplifi er Specifications Dual Band 800/1900 MHz Specifications Model Number 811210 Connectors FME-Male Impedance (input/output) 50 Ohms Dimensions 5 x 3.5 x 1.2 inch or 12.7 x 8.9 x 3 cm Weight 1.03 lbs or 0.468 kg Frequency 824-894 MHz / 1850-1990 MHz 1Passband Gain (nominal) 800 MHz (uplink/downlink) 26 dB / 26 dB 1900 MHz (uplink/downlink) 26 dB / 26 dB 220 dB Bandwidth (nominal) 800 MHz (uplink/downlink) 53 MHz / 62 MHz 1900 MHz (uplink/downlink) 112 MHz / 110 MHz .Power output for single cell phone (uplink) 800 MHz 1900 MHz CDMA +33.0 dBm +29.3 dBm GSM +34.3 dBm +30.3 dBm EDGE +34.1 dBm +30.2 dBm AMPS +30.1 dBm Power output for single received channel (downlink) 800 MHz 1900 MHz CDMA +5.1 dBm +6.8 dBm GSM +3.2 dBm +4.4 dBm EDGE +3.2 dBm +4.6 dBm AMPS +3.2 dBm 4Power output for multiple received channels (downlink). The maximum power is reduced by the number of channels: Number of channels Maximum Power 800 MHz 1900 MHz 2 +1.0 dBm +1.7 dBm 3 -2.5 dBm -1.8 dBm 4 -5.0 dBm -4.3 dBm 5 -7.0 dBm -6.3 dBm 6 -8.5 dBm -7.8 dBm Noise Figure (typical) Isolation 3.5 dB nominalupli...
Otros modelos de este manual:Avtousiliteli - Car Amplifier (293.36 kb)
Avtousiliteli - Car Amplifier (293.36 kb)