Iniciar sesión:
Votos - 1, Puntuación media: 5 ( )

Manual de usuario Directed Audio, modelo A404

Fabricar: Directed Audio
Tamaño del archivo: 455.52 kb
Nombre del archivo: 34512010_Directed_Audio_A502_Owners_Manual.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain setting on the amplifier and start to raise the head unit volume again. When you can listen to the music at or slightly above 3/4 on your head unit without audible distortion, slowly raise the gain of the amplifier until distortion is heard, then back off the gain until the distortion is not audible. This setting will allow you to reach full output with all but the quietest of source material, while avoiding excessive noise in the system. • The same procedure should be used for adjusting the amplifier when the on-board crossover is set to LPF or HPF, but you will also have to take into consideration the effect that gain adjustment has on system frequency response and imaging. Again, plan on spending some time with music that you know, getting the gain and crossover settings the way you like. Test discs and analyzers may help with this process, but in the end it's your ears that count - listen to the music! © 2004 Directed Electronics, Inc LED TUBE INSTALLATION (OPTIONAL) This Directed Audio amplifier has been designed with a custom heat sink that can accommodate two (optional—not supplied) VARAD LED tubes. 1. Before installing the LED tubes, remove and discard the mounting feet from the VARAD LED tubes. 2. Slide each LED tube assembly into your Directed Audio amplifier heat sink. Ensure that the LEDs are facing out for optimal visibility. The wires from the LED tube assembly should be on the signal input end of the amplifier. The Black wire from the LED tube is ground and the Black/White wire from the LED tube is power. 4. Run the two wires from the tube assembly and connect them to the 4-pin LED/FAN input connector. Refer to the LED/FAN harness diagram given earlier in this manual. N NNO OOT TTE EE: ::If the optional fan IS NOT being used, it is recommended that the second LED tube be wired to this circuit. If the optional fan is being used, it is recommended that the second LED tube be wired in parallel with the first LED tube. Use the following cross reference chart to select the proper length VARAD LED tube for use with your Directed Audio amplifier. Directed Amplifier—VARAD Cross Reference Chart Directed Part Number Directed Model VARAD Model QTY Required 45120 A502 HLX6, HL6, HLW9 2 45125 A802 HLX6, HL6, HLW9 2 45150 A404 HLX6, HL6, HLW9 2 45155 A1004 HLX12, HL12, HLW15 2 45095 D600 HLX6, HL6, HLW9 2 45100 D800 HLX6, HL6, HLW9 2 45105 D1200 HLX6, HL6 2 45110 D2400 HLX12, HL12 2 45165 D2205 (2) HLX12, (2) HL12 2 or 4 © 2004 Directed Electronics, Inc CEA SPECIFICATIONS AA550022 Power Output: 90 Watts RMS x 2 at 4 ohms and < 1% THD+N Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms) Additional Power: 125 Watts RMS x 2 at 2 ohm and < 1% THD+N AA440044 Power Output: 45 Watts RMS x 4 at 4 ohms and < 1% THD+N Signal to Noise Ratio: -80 dBA (reference 1 Watt into 4 ohms) Additional Power: 50 Watts RMS x 4 at 2 ohm and < 1% THD+N © 2004 Directed Electronics, Inc SPECIFICATIONS A AA 5 55 0 00 2 22 A AA 4 44 0 00 4 44 RMS continuous Power 4 Ohm 1 75W x 2 35W x 4 RMS continuous Power 2 Ohm 2 125W x 2 50W x 4 RMS continuous Power Bridged 4 Ohm 3 250W x 1 100W x 2 Dynamic Power Rating (IHF-202 Standard) 4 Ohms 200W 300W Signal-to-Noise Ratio Greater than 90 dB Greater than 90 dB Frequency Response 20-20,000 Hz ± 0.25 dB 20-20,000 Hz ± 0.25 dB Damping Factor Greater than 100 Greater than 100 Crossover Switchable high or low pass 12 dB/octave,100Hz Switchable high or low pass 12 dB/octave,100Hz Bass Equalization +8 dB, centered at 40Hz +8 dB, centered at 40Hz Input Impedance 20K ohms 20K ohms Input Sensitivity Variable from 250 mV to 7.5 volts Variable from 250 mV to 7.5 volts Output Impedance 2 to 8 ohms, stereo 4 to 8 ohms, bridged 2 to 8 ohms, stereo 4 to 8 ohms, bridged Supply Voltage 10 to 16 VDC 10 to 16 VDC Fusing and Power 30A 30A Minimum Cable Requirements (AWG) (Per amp, trunk mounted) #10 #10 1. RMS continuous power driven into 4 ohms from 20 to 20,000 Hz @ 14.4VDC with less than 0.08% THD+N. 2. RMS continuous power driven into 2 ohms from 20 to 20,000 Hz @ 14.4VDC with less than 0.15% THD+N. 3. RMS continuous power bridged into 4 ohms from 20 to 20,000 Hz @ 14.4VDC with less than 0.15% THD+N. © 2004 Directed Electronics, Inc Directed Electronics, Inc. The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest Vista, California 92081 vehicle security, car stereo products, rear seat entertainment, and accessories avail...

Otros modelos de este manual:
Avtousiliteli - A502 (455.52 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría