Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Carson Manufacturing Co., Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual. TB0354A Page 2 of 8 09/27/05 INSTALLATION Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before installing the unit. Failure to follow these instructions can cause serious damage to the unit or vehicle and may void warranties. SAFETY PRECAUTIONS For the safety of the installer, vehicle operator, passengers and the community please observe the following safety precautions. Failure to follow all safety precautions and instructions may result in property damage, injury or death. Qualifications -The installer must have a firm knowledge of basic electricity, vehicle electrical systems and emergency equipment. Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) Mounting - Mount the unit for easy access by the vehicle operator. DO NOT mount in air bag deployment area. Assure clearances before drilling in vehicle. To prevent internal damage mounting bolts must not enter case more than 1/4". Wiring - Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to vehicle battery. Testing - Test all siren functions after installation to assure proper operation. Test vehicle operation to assure no damage to vehicle. Keep These Instructions - Keep these instructions in the vehicle or other safe place for future reference. Advise the vehicle operator of the location. MOUNTING The mounting bracket supplied can be installed above or below the unit. Choose a mounting location convenient to the operator and away from any air bag deployment areas. Inspect behind mounting area for clearance. Assure adequate ventilation to prevent overheating. Consider wire routing and access to connections, as well as microphone bracket placement. Install mounting bracket to vehicle using 1/4" hardware (not supplied). If mounting in a rack or console, make sure that mounting bolts do not enter case more than 1/4". A microphone clip along with mounting screws (CP3633) holds the microphone in place. 1/4-20 Bolt (CP3966) Bolt must not pass through cover more than 1/4. CP3571 Mounting Bracket TB0354A Page 3 of 8 09/27/05 INSTALLER-SELECTABLE OPTIONS Carefully cutting programming resistor jumpers or traces on the printed circuit FUSE T- T AUX I PHSR CUT P AUX P board inside the case can select various options. The cover must be removed to access the jumpers. The cover is held in place by a snap-fastener on the back of the unit. Hold the unit with the front case flange on the edge of a hard surface and press hard on the back of the unit. The chassis will slide out the front of the cover. OPTION JUMPERS Auxiliary Input Function - The auxiliary input normally activates the Horn function. Do not cut the jumper resistor labeled "AUX I". Auxiliary Input Polarity - The auxiliary input is normally activated by connecting to positive. To activate by connecting to ground cut the two jumper resistors labeled "AUX P". Cutout Input Polarity - The cutout input is normally activated by connecting to positive. To activate by connecting to ground cut the two jumper resistors labeled "CUT P". Two-Tone - Not available, do not cut the jumper resistor labeled "T-T". Phaser Disable - The Phaser function is disabled, do not cut the jumper resistor labeled "PHSR". Horn Disable - The Horn function can b e disabled by cutting the trace on the back of the Cut to Disable horn board at the location designated "cut to disable horn". TB0354A Page 4 of 8 09/27/05 ELECTRICAL CONNECTIONS Disconnect vehicle battery before making any electrical connections. Electrical connections to the unit are made using a removable terminal block plug located on the back. A label on the unit identifies the terminal function. You should install the connector on the unit before wiring. If the unit needs service the connector can be easily removed without unwiring the connector. The power supply of the unit must be capable of delivering peak currents up to 50 amps for adequate short circuit protection and reliable operation. The preferred source is directly at the vehicle battery. The unit is internally fused. Attach leads by stripping 3/8", inserting into connector and clamp by tightening screw. Make sure the screw is tight and the wire can’t be pulled out. Failure to adequately tighten the scr...