Votos - 6, Puntuación media: 3.5
(
)
)
|
Resumen del manual
At this time the Back Up Valve will pull the Legend® II away from problem areas. Occasionally some vinyl pools have steps installed so the unit may not climb and remains stationary until the Back Up Valve pulls the unit away from the steps. When this occurs you need to use the optional Step Adapter (Part# EU13) to prevent wearing the vinyl liner. The Sweep Hose operates in a gentle sweeping motion to prevent debris from becoming trapped in hard to reach corners of the pool. LEGEND® II INSTALLATION MANUAL II. Installation Instructions A. Legend® II Components The Legend® II Box Contains: 1. Cleaner Head 2. Sand & Silt Bag 3. Sweep Hose 4. Complete Feed Hose a. 1 - 18 in. hose b. 1 - 2 ft. hose c. 1 - 4. ft. hose d. 3 - 6 ft. hoses e. 1- Back-Up Valve f. 4 - Swivels g. 1 - Wall Fitting h. 12 - Mender Nuts i. 7 - Hose Floats j. 1 - Pressure Tester B. Pool Connections The Legend® II comes equipped to connect to a female threaded 1-1/2" dedicated return line. An adjustable gate valve with a pressure gauge should be installed to allow a regulated amount of water flow from your pool system to the Legend® II. For more information contact our Technical Support Department at 1-800-831-7133. Also, if the pool doesn't have a dedicated cleaner line please contact our Technical Support Department also. C. Installing the Twist Lock Pressure Relief Valve (Wall Fitting) 1. Take out any existing pool cleaner and/or wall fitting. 2. Turn on the filtration pump and flush out the plumbing line. 3. Turn off filter pump 4. Remove the Wall Adapter from the Wall Fitting and screw Adapter by hand into the dedicated line. Turn until tight. 5.Take the Wall Fitting and Twist Lock the Wall Fitting into the Wall Adapter 1/4 turn; to a snug fit. Once the Wall Adapter is secure you can now twist lock and unlock to remove Wall Fitting with ease from the Wall Adapter. LEGEND® II INSTALLATION MANUAL D. Pressure Testing Instructions 1. Make sure the pool filter is clean before conducting this pressure test. 2. Twist lock the Wall Fitting with Feeder Hose into the Wall Adapter. 3. Have someone hold the Pressure Tester end of the Feed Hose beneath the water while you turn on the pool pump. Continue holding the hose under the water and cover the large hole of the pressure tester. 4. Reach down and feel around the Pressure Relief Valve on the Wall Fitting to see if the Relief Valve is releasing any water pressure. If valve is releasing water pressure go on to section E. If it is not, the pool filtration pump may not have sufficient amount of water pressure to operate the Legend® II. BEFORE YOU GO TO THE NEXT STEP, CONTACT OUR TECHNICAL SUPPORT DEPARTMENT AT: 1-800-831-7133 E. Cutting the Feed Hose (See Hose Diagram on Page 11) The Hose assembly comes in 6 sections covering approximately 30 ft. of the pool, which provides ample hose for most residential pools. For larger or smaller pools see Page 12 for instructions for Adding or Deleting Additional Feeder Hose. 1. Take Feeder Hose out of box and lay the hose straight in the sun for one day if possible, (this will take any memory out of the hose due to being coiled up in the box). 2. With the pool pump on, hold the free end of the Feeder Hose underwater. Gently pull the hose to the farthest end of the corner of the pool, do not stretch the hose. (The Legend® II usually will not climb the top step, so you do not need to include it in the measurement.) If the hose just reaches the farthest point of your pool, and without any excess hose hanging over the deck, then go to Section F. 3. If the Feeder Hose extends past the farthest end of the pool, mark the excess hose hanging over the deck, turn off your pool pump, and cut first 6 ft. section of hose, closest to the wall, the length of excess. 4. IMPORTANT: Please double check the hose length to insure you will be getting the maximum performance from your pool cleaner. The hose lengthens when under pressure (when your pump is on). LEGEND® II INSTALLATION MANUAL F. Hooking up the Legend® II 1. Remove the Pressure Tester from the free end of the Feeder Hose by unscrewing the Hose Nut. Left hand thread (reverse), (see illustration previous page). 2. Place mender nut on Legend® II Swivel Mast. Connect the open end of the Feed Hose to the top of the Legend® II Swivel Mast and secure with the mender nut. The arch of the Feed Hose should align in the same direction as the Swivel Mast, there should be no twist in the Feed Hose after connection. (See illustration below.) 3. Carefully twist lock the Sand & Silt debris bag onto the top of the Legend® II Vacuum Tube. Make sure there is a Rubber Debris Valve attached to the top of the Vacuum Tube before locking on the Sand & Silt bag, (this valve is similar to a check valve to help keep debris inside the bag when the water pressure is off). 4. Gently place the Legend® II in the pool. Turn on the pool filtration pump. 5. Check to make sure the wheel RPM is between 25-32. See page 5 for instructions on wheel RPM. G. C...