Iniciar sesión:
Votos - 5, Puntuación media: 4.2 ( )

Manual de usuario Swim'n Play, modelo side deck

Fabricar: Swim'n Play
Tamaño del archivo: 1.11 mb
Nombre del archivo: 8dc54b4a-b3de-4e2e-b53e-f0d16c141caf.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


DANGER DO NOT DIVE OR JUMP into your pool. Your pool is approximately 4' deep. It is not designed for diving or jumping. If you dive or jump into your pool you run the risk of permanent injury or death. Alert all visitors and family of this and point out all warning labels supplied. ADULT SUPERVISION REQUIRED 313 REGINA AVENUE RAHWAY, NEW JERSEY 07065-4891 Phone: (732) 574-1500 Fax: (732) 574-1551 E-mail: info@swimnplay.com Part # 420865-10 GENERAL Take time to follow the instructions and do things right the first time. Read all instructions prior to starting. Before you start, check to see that you have the correct number of parts. Use your parts list which is broken down by carton. The manufacturer reserves the right to revise, change or modify construction of their product. CONTRACT INSTALLATIONS The manufacturer is in no way affi liated with any professional installer. Therefore the manufacturer can assume no responsibility, for errors in installation by the home owner or said professional installer. If you have your deck installed by others, please supervise to be sure they comply with the proper installation techniques shown. Their past experience or short cuts may not cover the latest improvements in our decks. Do not allow any short cuts of any nature. LOCAL CODES Local building code may require obtaining a building permit and may have regulations on set backs, barriers, devices and other conditions that must be followed. Any after market or home built deck should be built to the local building code requirements, including load capacity and fencing requirements. Local electrical code may require obtaining a building permit and may have regulations on setbacks, devices and other conditions that must be followed. All electrical outlet connections should be a minimum of 5 feet from the outside perimeter of the wall of the pool. From 5-10 feet there should be either a fixed connection (outlet box) or twist- lock connection with a GFCI. Connect power cords to a 3-wire grounding-type outlet only. Severe electrical shock could result if you install your pump or filter on a deck. They could fall into the water, causing severe shock or electrocution. Do not install on a deck or other surface at, above or slightly below the top SEAT of the pool. BARRIER REQUIREMENTS If the distance from the top of the assembled pool is less than 48” vertically from the surrounding grade, a fence or barrier is needed to surround the pool with a minimum height of 48”. A barrier is necessary to provide protection against potential drowning and near drowning and is not a substitute for constant supervision of children. A barrier is a fence, wall, or a combination thereof which completely surrounds the swimming pool and obstructs access to the swimming pool. Barriers must comply with local and national building codes and the US Consumer Product Safety Commission. These are minimum fencing and barrier requirements. Check your local building codes for other requirements they may request. Optional fencing kits are available, Please contact your local dealer. If pool covers are used for safety barriers they should comply with ASTM F 1346 “Standard Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs.” GETTING STARTED Unpack and identify all the parts to your deck using the enclosed packing list. TO ASSEMBLE THE DECK YOU WILL NEED: 1. DRILL WITH A 7/64", 5/32", 3/16" AND 5/16" BIT 2. 7/16" WRENCH 3. #3 POINT PHILLIPS SCREW DRIVER 4. MEASURING TAPE AND MARKING PENCIL ATTENTION DECKS ARE MADE FOR 52 INCH DEEP POOLS IF YOUR POOL IS 48" DEEP YOU WILL HAVE TO DIG A TRENCH OR CUT THE BOTTOM OF THE POSTS (4 INCHES) IN ORDER TO LEVEL THE HEIGHT OF THE DECK WITH THE HEIGHT OF YOUR POOL. THE BASE OF THE DECK MUST BE LEVEL WITH THE TOP LEDGE OF YOUR POOL 2 ASSEMBLY DRAWINGS Use the drawings below for reference while assembling your deck. During assemly please note that the ledges on the pool are to be removed where the deck meets the pool. The extension on the front of the deck will replace your pool legde. Please refer to Step 9. Deck Deck Deck Deck Ledge Ledge Ledge Ledge 1. x 5 LEFT 4 x 5 4 x 5 4 x 5 1. x 5 RIGHT 1. x 5 LEFT 4 x 5 4 x 5 1. x 5 RIGHT Deck Deck Ledge Ledge Deck Deck Ledge Ledge 1. x 5 1. x 5 4 x 5 4 x 5 LEFT RIGHT 1. x 5 1. x 5 4 x 5 4 x 5 4 x 5 LEFT RIGHT Deck Deck Ledge Ledge Deck Deck Ledge Ledge 1. x 5 1. x 5 4 x 5 LEFT RIGHT 1. x 5 1. x 5 4 x 5 4 x 5 4 x 5 4 x 5 4 x 5 4 x 5 LEFT RIGHT 3 LEVEL GROUND 1 Clear out and level the ground in the location where A your deck is to be installed. Use the following chart for the area size: SIZE A B 12 x 18 8 ft. 6 ft. 12 x 24 12 ft. 6 ft. 15 x 24 12 ft. 6 ft. 15 x 30 16 ft. 6 ft. 18 x 33 16 ft. 6 ft. 18 x 45 28 ft. 6 ft. POOL DECK B If the vertical or Buttress post do not have pre-drilled holes, simply measure down the required distance from the top and place the bracket on the post or vertical as sh...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría