Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Remington Tamaño del archivo: 954.91 kb Nombre del archivo: Idioma del manual:

Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. Guide Bar Nuts Guide Bar Correct Tension Incorrect Tension Figure 5 - Turning Adjusting Screw Figure 6 - Saw Chain Adjustment Guide Bar Gap 4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension. OWNER’S MANUAL OPERATING CHAIN SAW Continued OILING CHAIN Always check oil level before using saw. To oil chain, press oil cap. Oil will feed onto guide bar and chain. Press oil cap at least once before each cut. Check oil level often by looking at oil sight level hole. Oil sight level hole is on left side of saw, between front handle and front hand guard. Figure 8 - Pressing Oil Cap to Oil Chain CUTTING WITH THE CHAIN SAW 1. Connect saw to extension cord. Connect extension cord to power supply. 2. Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain. 3. Use both hands to grip saw. Always use left hand to grip front handle and right hand to grip rear handle. Use firm grip. Thumbs and fingers must wrap around saw handles (see Figure 9). 4. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Stand slightly to left side of saw. This keeps your body from being in direct line with chain. 5. When ready to make a cut, press in switch lockout with right thumb and squeeze trigger (see Figure 9). This will turn saw on. Releasing trigger will turn saw off. Make sure saw is running at full speed before starting a cut. 6. When starting a cut, place moving chain against wood. Hold saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw. 7. Guide saw using light pressure. Do not force saw. The motor will overload and can burn out. 8. Remove saw from a cut with saw running at full speed. Stop saw by releasing trigger. Do not use the chain brake. Make sure chain has stopped before setting saw down. 9. Practice until you can maintain a steady, even cutting rate. Front Hand Switch Guard Trigger Lockout Figure 9 - Front Hand Guard, Switch Lockout, and Trigger Location TRIMMING A TREE (Pruning) WARNING: Avoid kickback. Kickback can result in severe injury or death. SeeKickback, page 3 to avoid risk of kickback. WARNING: Do not operate chain saw while • in a tree • on a ladder or any other unstable surface • in any awkward position You may lose control of saw causing severe injury. WARNING: Do not cut limbs higher than your shoulders. Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. Make first cut 15 centimeters (six inches) from tree trunk on underside of limb. Use top of guide bar to make this cut. Cut 1/3 through diameter of limb (see Figure 10). 2. Move five to ten centimeters (two to four inches) farther out on limb. Make second cut from above limb. Continue cut until you cut limb off. 3. Make third cut as close to tree trunk as possible on underside of limb stub. Use top of guide bar to make this cut. Cut 1/3 through diameter of stub. 4. Make fourth cut directly above third cut. Cut down to meet third cut. This will remove limb stub. CAUTION: Seek professional help if facing conditions beyond your ability. 2nd Cut Pruning Cut (to avoid 4th Cut - Final pinching) Figure 10 - Cutting A Limb 5 to 10 cm (2" to 4") 1st Cut - Pruning Undercut (to avoid splintering) (6") 3rd Cut - Stub Undercut 15 cm Stub Cut (to avoid splintering) Continued 100583 9 ® ® ELECTRIC CHAIN SAW OPERATING CHAIN SAW Continued FELLING A TREE (Cutting D...

Descargar ahora

Introduzca dos números de la imagen: