Votos - 4, Puntuación media: 3.8 ( )

Fabricar: Remington Tamaño del archivo: 954.91 kb Nombre del archivo: Idioma del manual:

Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. ments when used with other saws. Keep this manual for reference. It is your guide to safe and proper operation of this chain saw. 100583 5 ® ® ELECTRIC CHAIN SAW PRODUCT IDENTIFICATION Power Cord Rear Handle Rear Hand Guard Spike Saw Chain Guide Bar Nose Guide Bar Front Hand Guard Oil Level Sight Hole (located on saw body, hidden by front handle) Front Handle Motor Housing Trigger Switch Lockout Oil Cap Figure 2 - Electric Chain Saw UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought chain saw. ASSEMBLY Note:Some models are pre assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, page 8. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. The plastic hardware bag should include: • two guide bar bolts • two guide bar nuts • one Phillips-head tapping screw 1. Lay chain out flat. 2. Install front hand guard onto saw body. Do this by pressing two mounting standouts on hand guard into hex-shaped holes in saw body (see Figure 3). 3 Insert tapping screw through hand guard and into saw handle. Tighten screw firmly. 4. Turn adjusting screw counterclockwise (see Figure 4). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate and sprocket support. IMPORTANT: Make sure to insert adjusting block into oval adjusting hole on guide bar. 6. Line up holes on sprocket support with center slot on guide bar and holes in saw body. 7. Insert guide bar bolts through front hand guard, saw body, center slot of guide bar, and sprocket support. Attach guide bar nuts to guide bar bolts. IMPORTANT: Tighten guide bar nuts finger tight only. Make sure adjusting block is in oval adjusting hole on guide bar. 8. Place chain around drive sprocket, then along top groove of guide bar and around guide bar nose. Note:Make sure cutting edges of chain are facing the right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 3). CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment, page 8. 6 100583 OWNER’S MANUAL ASSEMBLY Continued Front Hand Guard Tapping Screw Towards Guide Bar Nose Cutting Edge Drive Sprocket Guide Bar Bolts Guide Bar Nuts Adjusting Hole Saw ChainCutting Edge Guide Bar Mounting Stand-Outs FILLING OIL TANK 1. Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note:For temperatures below -1°C, use SAE #10 oil. For temperatures above 24°C, use SAE #40 oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank. 4. Wipe off excess oil. Note:It is normal for oil to seep when saw is not in use. Empty oil tank , tighten oil cap, and store upside down after each use to prevent seepage. Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Screw Adjusting Plate Sprocket Support Figure 4 - Part Locations For Assembling Guide Bar 100583 7 8 100583 ELECTRIC CHAIN SAW ® OPERATING CHAIN SAW WARNING ICON G 001 WARNING: Read and understand this owner’s manual before operating this saw. Make certain you read and understand all Safety Warnings. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood. EXTENSION CORDS Use proper extension cord with this chain saw. Use only extension cords marked fo...

Descargar ahora

Introduzca dos números de la imagen: