Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Assembly is not needed on these models. See Saw Chain Tension Adjustment. 1. Lay chain out flat. 2. Loosen and remove guide bar nuts and sprocket cover. 3. Loosen and remove drive sprocket screw or remove E-ring from shaft (see Figure 4). Remove sprocket support. 4. Install guide bar onto saw body. Assemble center slot of guide bar onto guide bar bolts. 5. To replace sprocket support, repeat step 3 in reverse order. Firmly tighten drive sprocket screw with #2 Phillips screwdriver (if applicable). 6. Place chain around drive sprocket, along top groove of guide bar, and around guide bar nose. Note: Make sure cutting edges of chain are facing in right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 4, and indicator on side cover of saw). WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. 7. Insert tab of sprocket cover into slot on side cover and rotate sprocket cover onto guide bar bolts until sprocket cover rests against guide bar. 8. Place guide bar nuts, removed in step 2, over guide bar bolts. IMPORTANT: Tighten guide bar nuts fi nger tight only. 9. Turning chain tensioning knob (Model 107625 -02, 111174-01) or chain tensioning screw (Model 107624-02), adjust position of adjustment block until it is aligned and inserted into the round adjusting hole on guide bar (see Figure 4, 5and 6). Turning chain tensioning knob or chain tensioning screw counterclockwise will move adjustment block to rear of guide bar. Turning chain tensioning knob or chain tensioning screw clockwise will move adjustment block to front of guide bar. 10. If needed, readjust guide bar nuts to fi nger tight only. 11. Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment. CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. Figure 4 - Assembling Guide Bar and Chain Figure 5 - Turn Chain Tensioning Screw on Model 107624-02 Figure 6 - Turn Chain Tensioning Knob on Model 107625-02, 111174-01 Chain Tensioning Screw Adjustment Block Chain Tensioning Knob Adjustment Block E-Ring ASSEMBLY 10 LOOSEN LOOSEN Loosen both nuts... If chain becomes loose around guide bar, allow chain to cool then... TIGHTEN Turnchaintensioningscrewclockwise to tension saw chain or... Model 107624-02 TIGHTEN TIGHTENTIGHTEN Turn chain tensioning knob clockwise to tension saw chain... Pull chain to check tension. Guide links should not come out of guide bar groove... Make sure chain moves freely around guide bar then tighten both nuts. Guide Bar Models 107625-02, and 111174-01 Approx. 5/32" SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. IMPORTANT! Failure to follow these instructions when tensioning saw chain will damage saw and void the warranty. For additional information call 1-800-626-2237. New saw chains will stretch. Check chain tension frequently when fi rst used and tighten when chain becomes loose around guide bar. OPERATING CHAIN SAW WARNING: Read and understand this owner’s manual before operating this saw. Make certain you read and understand all Important Safety Information. Improper use of this chain saw can cause severe injury or death fromfire, electrical shock, or body contact with moving chain, or falling wood. FILLING OIL TANK 1. Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank. 4. Wipe off excess oil. Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage. Oil Sight Window Figure 8 - Oil Sight Window Location for Model 107625-02, 111174-01 EXTENSION CORDS Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below. ENGLISH IMPORTANT: DO NOT USE BAR AND CHAIN OIL OILING CHAIN Manual Oil System Always check oil level before using saw. Do not attempt to operate the oil system while saw is in operation. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least on...
Otros modelos de este manual:Benzo y sierras - 107624-02 (1.78 mb)
Benzo y sierras - 111174-01 (1.78 mb)