Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• 5/32" round file • Depth gauge tool • File guide • Vise • Medium sized flat file Sharpening Cutters Use file guide for 30° filing. 1. Adjust chain for proper tension (see Saw Chain Tension Adjustment). 2. Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain. 3. Press 5/32" round file (attached to file guide) into groove between top plate and depth gauge on chain. File guide should rest on both top plate and depth gauge (see Figure 20). Note: File at midpoint of guide bar. Filing Direction30° Guide Mark File Guide 5/32" Round File Note: This illustration shows file guide placement and filing direction for sharpening cutters on left side of chain. Figure 20 - File and File Guide Placement On Chain Depth Gauge (right Depth Gauge (left Right Side of ChainGrooveTop Plate (right side of chain) side of chain) side of chain) Groove Top Plate (left side of chain) Figure 21 - Chain Part Locations 4. Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 20). This will insure that you file cutters at 30° angle. 5. File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 20). Note: Two or three strokes with file should sharpen cutter. 6. After each cutter is sharpened, move chain forward to sharpen next cutter. File all cutters on one side of chain. 7. Move to other side of chain and repeat process. Filing Cutter Depth Gauges The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges. 1. Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 22). 2. Use medium flat file. File depth gauge level with depth gauge tool. 3. Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 23). After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing. REPLACING SAW CHAIN Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Parts and Accessories. Flat File Depth Gauge Slot Depth Gauge Tool Depth Gauge Figure 22 - Depth Gauge Tool On Chain Front Corner .025" .635 mm Figure 23 - Round Off Front Corner Of Depth Gauge ENGLISH 17 REPLACEMENT CHAINS Replacement saw chains may be available at your local hardware or home improvement store. The following list gives the specifications for replacement chains. All chains will be .050 gauge, 3/8 pitch. 14" chains have 56 drive links 16" chains have 58 drive links You may also order the replacement saw chains from the "Online Outlet" at com using the part number listed in the illustrated parts list on pages 63-66 of this manual. STORAGE If storing saw for more than 30 days, follow steps below. 1. Drain oil tank after each use. 2. Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture. 3. Dry guide bar and chain. 4. Place chain in container filled with oil. This will prevent rust. 5. Wipe a thin coating of oil over surface of guide bar. 6. Wipe off outside of saw body. Do this with soft cloth dampened with a mild soap and water mixture. 7. Store chain saw • in a high or locked place, out of children’s reach • in a dry place • in a carrying case or with scabbard over guide bar TECHNICAL SERVICE You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at remingtonpowertools.com or contact our Technical Service Department at 1-800-626-2237 (English Only). You may also write to: DESA Power Tools ATTN: Technical Service P.O. Box 90004 Bowling Green, KY 42102-9004 When contacting DESA Power Tools, have ready • Your Name • Your Address • Your Phone Number • Model Number of Product • Date of Purchase (Include copy of receipt for written requests). We reserve the right to amend these specifi cations at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty expressed or implied. REPLACEMENT PARTS AND ACCESSORIES WARNING: Use only replacement parts and accessories described in this manual. Use of other parts or accessories could damage saw or injure operator. For original replacement parts and accessories, contact your nearest Authorized Dealer or Authorized Service Center for this product. If they can not supply the part or accessory, contact your nearest Parts Central listed on page 67. Each Authorized Dealer, Authorized Service Center, and Parts Central is independently owned and operated. See pages 63 through 66 for an Illustrated Parts ...
Otros modelos de este manual:Benzo y sierras - 107624-02 (1.78 mb)
Benzo y sierras - 107625-02 (1.78 mb)