Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Never try to fell the tree that is trapped. Never work in the risk zone of the hanging trapped tree. The safest method is to use a winch. • Tractor-mounted • Portable Cutting trees and branches that are in tension Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more). Decide which is the safest way to release the tension and whether you are able to do it safely. In complicated situations the only safe method is to put aside your chain saw and use a winch. General advice: Position yourself so that you will be clear of the tree or branch when the tension is released. Make one or more cuts at or near the point of maximum tension. Make as many cuts of sufficient depth as necessary to reduce the tension and make the tree or branch break at the point of maximum tension. Never cut straight through a tree or branch that is in tension! If you must cut across tree/limb, make two to three cuts, one inch apart, one to two inches deep. Continue to cut deeper until tree/limb bends and tension is released. Cut tree/limb from outside the bend, after tension has been released. How to avoid kickback What is kickback? The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object. Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it ! WARNING! Kickback can happen very suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique. WORKING TECHNIQUES was being used when the kickback zone of the bar touched the object. Kickback only occurs if the kickback zone of the bar touches an object. Limbing Cutting the trunk into logs See instructions under the heading Basic cutting technique. ! WARNING! A majority of kickback accidents occur during limbing. Do not use the kickback zone of the guide bar. Be extremely cautious and avoid contacting the log, other limbs or objects with the nose of the guide bar. Be extremely cautious of limbs under tension. They can spring back toward you and cause loss of control resulting in injury. Make sure that you can stand and move about safely. Work on the left side of the trunk. Work as close as possible to the chain saw for maximum control. If possible, let the weight of the chain saw rest on the trunk. Keep the trunk between you and the chain saw as you move along the trunk. 30 – English MAINTENANCE General The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. Carburetor adjustment Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. Function • The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine. • The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed. Basic settings and running in The basic carburetor settings are adjusted during testing at the factory. Fine adjustment should be carried out by a skilled technician. Rec. idle speed: See the Technical data section. Fine adjustment of the idling speed T Adjust the idle speed with the T-screw. If it is necessary to re-adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate.Then turn counterclockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the chain starts to rotate. ! WARNING! Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired. Correctly adjusted carburetor When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine. Checking, maintaining and servicing chain saw safety equipment Note! All servicing and repair work on the machine requires special training....
Otros modelos de este manual:Benzo y sierras - CS 2245 (2.94 mb)
Benzo y sierras - CS 2245S (2.94 mb)