Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the saw chain at the nose of the guide bar contacts an object. Kickback can lead to dangerous loss of control of the chain saw. 19. When transporting your chain saw, make sure the appropriate guide bar scabbard is in place. 20. This chain saw is equipped with a spark arrester built-in muffler. Periodically check the arrester to keep it in good order. KICKBACK SAFETY PRECAUTIONS FOR CHAIN SAW USERS – WARNING – . Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. . Do not rely exclusively on the safety devices built into your saw. As a chain saw user you should take several steps to keep cutting jobs free from accident or injury. (1) With a basic understanding of kickback you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. (2) Keep a good grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle, when the engine is running. Use a firm grip with thumbs and fingers encircling the chain saw handles. A firm grip will help you reduce kickback and maintain control of the saw. Don’t let go. (3) Make certain that the area in which you’re cutting is free from obstructions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw. (4) Cut at high engine speeds. (5) Do not overreach or cut above shoulder height. (6) Follow manufacturers sharpening and maintenance instructions for saw chain. (7) Only use replacement bars and chains specified by the manufacturer or the equivalent. .6 . SE5 .7 . 50:1 MIXING CHART GASOLINE gal. 1 2 3 4 5 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 GASOLINE liter 1 2 3 4 5 2-CYCLE OIL ml 20 40 60 80 100 .9 . .10 . ¦ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely. 1. Select bare ground for fueling. 2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine. 3. Stop the engine before refueling the unit. It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. ¦ STARTING ENGINE Keep clear of the saw chain as it will start rotating upon starting of the engine. 1. Continuously push the priming bulb until fuel comes in the bulb. (OP2) 2. Put the ignition switch to “ I ” position. (OP2) 3. While holding the throttle lever together with the throttle interlock, push in the side button and release the throttle lever to hold it at the start position. (OP3) 4. Pull out the choke knob to the closed position. (OP4) When restarting immediately after stopping the engine, Ieave the choke knob at the open position. NOTE WARNING WARNING WARNING 7. Operation OP1 OP2 OP3 OP4 NOTE WARNING WARNING WARNING 7. Operation OP1 OP2 OP3 OP4 OP5 .11 . OP8 7. Operation NOTE •When the brake worked, immediately release the throttle lever and slow down the engine speed. Running the engine at high speed while braking the saw chain can cause clutch failures. • Before starting the day's job, check the condition of the brake system as follows: 1) Start the engine and grasp the handles securely with both hands. 2) While pulling the throttle lever, slowly push the brake lever (front hand guard) forward with the back of your left hand. 3) Check that the brake works normally, then release the throttle lever. 4) Pull the brake lever back to the OFF position. .13 . 8. Sawing NOTE • Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • Racing the engine with the chain seized in a cutaway can damage the clutch system. When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever to open the cut. ¦ GUARD AGAINST KICKBACK • This saw is equipped with a special ...
Otros modelos de este manual:Benzo y sierras - G3100T (586.4 kb)