Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Align the holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver. Parent Console Attachment The parent console will attach to the handle by snapping it in place on the handle and above the canopy. Operating Instructions Mall Cruiser™ 11-KS188...page 2 Front Wheel Assembly - {Figure 1.c} axle release lever Rear Wheel Assembly - {Figure 1.b} quick-releaselever (open position) Parts List: Description Qty. Frame assembly with seat, 1 canopy, and wrist strap Front Wheel 1 Parent Console 1 Under-seat Basket 1 Rear Wheels 2 Front Fender 1 #8 – 11.2" Phillips head screws 4 Tools Required: Phillips screw driver, adjustable wrench. Stroller Assembly Instructions Unfold Stroller: Remove from carton, and remove any packaging materials that may be holding the frame in closed position. Grasp frame handle and open. Lock both plastic latches, on sides, onto the lower frame, insert locking pin into hole in latch and frame, lock the pin in place by slipping the wire loop over the end of the lock pin, repeat for the other side. {see Figure 1.A} Rear Wheel Assembly Grasp rear wheel in one hand, slide wheel’s axle into hole in rear of frame. Push up on the axle release lever so that the wheel is fully inserted. Pull the wheel firmly, the wheel should not come off if fully inserted/locked. Repeat for other side. To release wheel push up on axle release lever and pull off wheel. Front Wheel Assembly Tip stroller back so that the handlebar is down on the ground and the front fork is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever on the front wheel far enough to allow the axle to slide into the front fork. With wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight, then flip wheel’s Q/R lever backward to the closed position to lock wheel in place. Note this step may require minor adjustment until the Q/R lever fl ips back with firm pressure. Pull outward on wheel to ensure it is locked in place. (photo = open and closed lever) Caution: The interior jam nuts are factory installed and do not need adjustment. NOTE:This product has a swivel wheel that can rotate or be locked in place. To lock or unlock the wheel use the switch placed on the top of the fork. The wheel should always be locked in place when used as a jogging stroller. {Figure 1.a} Front Fender Assembly Insert the #8 – 1.5" screws into the holes located on the front support above the wheel. Align the holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver. Parent Console Attachment The parent console will attach to the handle by snapping it in place on the handle and above the canopy. Operating Instructions Mall Cruiser™ 11-KS188...page 2 Front Wheel Assembly - {Figure 1.c} axle release lever Rear Wheel Assembly - {Figure 1.b} quick-releaselever (open position) Operating Instructions Mall Cruiser™ 11-KS188...page 3 Tether/Wrist Strap Attachment To recline seat The wrist strap has different sized loops. The large loop will go on your wrist; the small loop will be on handlebar. Slide end with large loop through the small loop, then grasp the end with the large loop and pull strap to tighten on handlebar. Caution: Whenever child is in stroller always use the wrist strap. Before you remove the wrist strap from your wrist make sure you first engage the rear brakes. Engage Parking Brake Step on the levers next to the rear wheels, or the metal bar that links the two levers, until the cogs of the brakes engage the cogs of the wheel. Repeat on other side. To release brake, lift levers using your toe until cogs disengage. Engaged Parking Brake Disengaged Parking Brake PROPER USE OF SEAT BELTS & SHOULDER STRAPS WARNING: Avoid serious injury from falling or sliding out. Always use seatbelt. Place child in seat. Make sure T-shield is between the child’s legs. When child is seated, place shoulder straps over the child’s shoulders. Slide waist straps through lower loops of shoulder straps, bring lap belt ends together and clip into place around child’s waist. Adjust waist and shoulder straps for snug fi t. To fully recline, unhook buckle on back of the seat.To adjust the recline position; adjust the slide on the strap to the desired length. WARNING: Child may slip into leg openings and strangle. Never use in a reclined carriage position unless T-shield and shoulder strap have been readjusted to the new seat position. Storage and folding WARNING: Always remove child from stroller before folding Pull the back of the seats forward. It will be easier to fold if the seats are not in the recline position. Remove locking pins from side latches on the stroller frame (Double Models have 2 locking pins). Release the two latches from the frame. The stroller may automatically begin to fold, the front wheel will fold under frame and the handle will fold backwards. For a more compact fold remove front and rear wheels Storage and folding Operating Instructions Mall Cr...