Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Follett Tamaño del archivo: 558.48 kb Nombre del archivo: Idioma del manual:

Crushed, flake, bagged, nugget or congealed ice cannot be used. Use of these ices can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to dispenser. For ice compatibility questions, please call Follett customer service at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301. 4 Specifications Electrical Each icemaker and dispenser require a separate circuit with with electrical disconnect within 10 ft (6m). Equipment ground required. Standard electrical – 115V, 60Hz, 1 phase. Maximum dispenser fuse – 15 amps, Maximum icemaker fuse – 20 amps each. Model Icemaker Dispenser number amperage amperage Single-sided models U155, U155X 2.4 amps U155B, U155BX 4.4 amps U155R400A/W, U155R400A/WX 11.0 amps 2.4 amps U155BR400A/W, U155BR400A/WX 11.0 amps 4.4 amps U155R800A/W, U155R800A/WX 11.0 amps ea (2) 2.4 amps U155BR800A/W, U155BR800A/WX 11.0 amps ea (2) 4.4 amps Plumbing Dispenser 3/4" PVC pipe nipple for bin drain 3/4" PVC pipe nipple for drain pan drain 1" ID hose for beverage bath drain Beverage connections 1/4" ID syrup beverage hose 3/8" ID carbonated water beverage hose 3/8" ID plain water beverage hose Note: Drains should be hard piped and insulated. Maintain at least 1/4" per foot (6mm per 304mm run) slope on drain line run. Water disconnect within 10 feet (3m) of dispenser is suggested for automatic load units. Follett recommends use of a Follett model AFSYSTMFL4S water filter on icemakers connected to automatic fill dispensers. Icemaker (detailed specifications may be found in icemaker installation manual packed with icemaker) 3/8" OD push-in water in 3/4" MPT drain 3/8" FPT condenser inlet (water-cooled condenser only) 1/2" FPT condenser drain (water-cooled condenser only) 5 Dimensions and clearances Required clearances 51" (1295mm) minimum above counter for installation if dispenser will be dropped into counter 36" (915mm) minimum above counter for all units after installation for auger cleaning and servicing 12" (305mm) minimum on side opposite ice chute for service 12" (305mm) minimum on ice chute side if ice transport tube enters this side 12" (305mm) minimum between dispenser side(s) and optional icemaker(s) 6" Front View 3/4 PVC slip joint drain 37.25" 17" (432 mm) 18.875"18.875" beverage line air break* electrical connections 31.25" (794mm) 21.75" (553mm) 28" (712mm) counter top ice transport tube 49.75" (1264mm) (8 valve unit) (10 valve unit) (947mm) 12" *DO NOT (479mm) min (479mm) min CONNECT TO DRAIN SYSTEM Manual load unit Automatic load unit with 1 icemaker Automatic load unit with 2 icemakers 27.375" (696mm) ice transport Side View tube entrance 6" (153mm) 25.8" (656mm) 8.75" 3/4 PVC slip joint drain 18.5" (470mm) beverage waterbath overflow beverage drain pan drain 3.5" (889mm) (223mm) power bin signal 6 Installation Installing dispenser in counter Note: All dispensers must be supported from below with supplied 6" - 9" (153 – 229mm) adjustable leg accessory, or equivalent. Do not hang dispenser on flange. All dispensers must be installed level in both directions to ensure proper operation. 1. Chec...

Descargar ahora

Introduzca dos números de la imagen: