Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Tall bottles should not be loaded on the bottom rack because they may prevent the door from closing. bottles facing rearbottles facing front All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Appliance Features Adjustable Temperature Control The temperature control is fully adjustable from 4163° F. The range allows flexibility of temperature preferences and provides the ideal wine aging and storing temperatures. Interior Light and Switch The interior light makes it easy to view your wine labels and enhances the display of your collection. When the switch is in the “OFF” position, the light will come on when the door is opened. Roll-out Racks The six-roll out wine racks may be pulled out approximately 14in (355mm) to facilitate adding or removing bottles. Do not lean on or press down heavily on the wine shelves. Doing so may damage the shelves and the wine bottles stored on them. Pull the wine racks out gently and carefully to minimize unsettling your wine collection. Avoid pulling out more than one rack at any time to maintain stability. Single Bottle Racks Because bottles are not stacked on top of each other, you can easily view and access your inventory without disturbing other bottles. All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Cleaning and Maintaining Your Wine Chiller Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year brush or vacuum lint and dirt from the grille. Also at least once or twice a year brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet. Cabinet The painted cabinet can be washed with mild soap and water and thoroughly rinsed with clear water. Never use abrasive scouring powders. Interior Wash interior compartment with mild soap and water. Do not use an abrasive powder, solvent, polish cleaner or undiluted detergent. Glass Door Use a glass cleaner or mild soap and water and soft cloth to clean the glass door model. Do not use any abrasive powders. Door Gasket The vinyl gasket may be cleaned with mild soap and water, a baking soda solution or a mild scouring powder. Light Tube Replacement WARNING! DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT TUBE REPLACEMENT. Failure to do so may result in an electrical shock that could severely injure you. This product uses two, 6 watt light tubes to illuminate the interior of the wine chiller. The light tubes are very reliable electrical components, but should either or both light tubes not function properly, please call the dealer you purchased your wine chiller from for replacement light tubes. Use only original equipment light tubes from your dealer or manufacturer. Light tube replacement consists of using a small cross head screwdriver to remove the two screws that hold a cover plate over the back section of the light tube. Set the screws and cover plate aside for re-assembly later. Using a small flat-blade screwdriver, gently lever the front section of the light tube down to allow it to be pulled clear of the light housing. Disconnect the two insulated electrical connectors from the cabinet’s electrical cable and discard the old light tube. Reconnect the insulated electrical connector of the new light tube to the cabinet’s electrical cable connectors. Make sure they are secure and fully inserted. Carefully realign the light tube’s electrical terminals back into the rear of the light enclosure channel making sure not to crimp them. Gently insert the light tube along the length of the light enclosure channel. Press the light tube gently into the light enclosure channel. Only a small part of the light tube should project below the ceiling of the wine chiller. DO NOT USE A HAMMER TO FIT THE LIGHT TUBE. Place the light tube terminal cover plate back in its original position on the light enclosure’s flange. Re-use the original two screws to secure it in place. Plug the wine chiller into the electrical socket. Check to see if the light tubes operate properly. Your light tube’s replacement is complete. The light tubes are not covered by your guarantee. Replacement tubes can be obtained from your service provider or from Aga Appliances. Light Tube Connectors Cover Plate Screws All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased produ...
Otros modelos de este manual:Dispensers - 6WCA (774.34 kb)
Dispensers - 115V (774.34 kb)
Dispensers - 6WCA (774.34 kb)