Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
CLOSURE................................................................................................................20 GENERAL MACHINE DATA ..............................................................................21 PART BREAKDOWN ........................................................................................22 PART LIST ........................................................................................................23 WARRANTY AND RETURNS............................................................................24 G4008/G4009 Drill Press -1 SECTION 1: SAFETY WARNING: For Your Own Safety Read Instruction Manual Before Operating Drill Press a) Always wear eye protection. b) Do not wear gloves, necktie or loose clothing. c) Clamp workpiece or brace against the column to prevent rotation. d) Use recommended speed for drill accessory and workpiece material. Safety Instructions For Power Tools These safety rules cannot cover every situation in a work shop. Consider your conditions when setting up or operating your drill press 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. 5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP KID PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure it is rated Hard Service (grade S) or better. Conductor size must be 16 A.W.G. for cords up to 100 feet in length. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged. Minimum Gage for extension cord: 16 A.W.G. 50ft 16 A.W.G. 100ft 14 A.W.G. 200ft 12 A.W.G. 300ft 10. WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. 11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. -2- G4008/G4009 Drill Press 12. SECURE WORK. Use clamps or a vise to 17. USE RECOMMENDED ACCESSORIES. hold work when practical. It’s safer than Consult the owner’s manual for recommend- using your hand and frees both hands to ed accessories. The use of improper accesoperate tool. sories may cause risk of injury to persons. 13. DON’T OVERREACH. Keep proper footing 18. CHECK DAMAGED PARTS. Before further and balance at all times. use of the tool, a guard or other part that is damaged should be carefully checked to 14. MAINTAIN TOOLS WITH CARE. Keep tools determine that it will operate properly and sharp and clean for best and safest perfor-perform its intended function - check for alignmance. Follow instructions for lubricating and ment of moving parts, binding of moving changing accessories. parts, breakage of parts, mounting, and any other conditions that may affect its operation. 15. DISCONNECT TOOLS before servicing and A guard or other part that is damaged should changing accessories, such as blades, bits, be properly repaired or replaced. cutters, and the like. 19. DIRECTION OF FEED. Feed work into a 16. REDUCE THE RISK OF UNINTENTIONAL blade or cutter against the direction of rota- STARTING. Make sure switch is in off posi-tion of the blade or cutter only. tion before plugging in. 20. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. Additional Safety Instructions For Drill Presses 1. Never use a bit with a tapered shank or 4. Feed the drill bit evenly into the workpiece. square bit in a drill chuck. Back the bit out of deep cuts to cool and clean the bit. 2. Remove metal cuttings with a brush, never by hand. 5. Never attempt to clean wood or metal cuttings from drill bits while the drill press is run 3. Never drill sheet metal unless it is securely ning. clamped to the table. 6. Work should be secured in such a way so as to avoid drilling into the table. G4008/G4009 Drill Press -3 SECTION 2: CIRCUIT REQUIREMENTS 110V Operation The G4008/G4009 Drill Press is supplied with a U.S made 110V/220V motor. Under normal use, the motor draws approximately 9 amps @ 110V. We recommend using a 15 amp circuit breaker or a 15 amp sl...
Otros modelos de este manual:Taladros y shuropopverty - G4008 (668.95 kb)