Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known ground. Never remove the third prong. 5. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it "on." 6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well-lighted. 8. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 9. MAKE WORKSHOP CHILDPROOF -with padlocks, master switches, or by removing starter keys. 10. DON'T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed. 11. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed. 12. WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. 13. ALWAYS USE SAFETY GLASSES. Wear safety glasses (must comply with ANSI Z87.1)~ Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. Also use face or dust mask if cutting operation is dusty. 14. SECURE WORK. Use clamps ora vise to hold work when practical. It's safer than using your hand and frees both hands to operate tool. 15. DON'T OVERREACH. Keep proper footing and balance at all times. 16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 17. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters, etc. 18. USE RECOMMENDED ACCESSORIES. The use of improper accessories may cause hazards or risk of injury to persons. 19. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in "OFF" position before plugging in power cord. 20. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 21. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 22. DIRECTION OF FEED. Feed work into a blade or cuttteragainst the direction of rotation of the blade or cutter only. 2 23. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it comes to a complete stop. 24. DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol or any medication. 25. MAKE SURE TOOL IS DISCONNECTED FROM POWER SUPPLY while motor is being mounted, connected or reconnected. 26. THE DUST GENERATED by certain woods and wood products can be injurious to your health. Always operate machinery in well ventilated areas and provide for proper dust removal. Use wood dust collection systems whenever possible. 27. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: •lead from lead-based paints, •crystalline silica from bricks and cement and other·masonry products, and •arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. ADDITIONAL SAFETY RULES FOR DRILL PRESSES 1. DO NOT operate your drill press until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the operation of drill presses, obtain advice from your supervisor, instructor or other qualified person. 3. YOUR DRILL PRESS MUST be securely fastened to a stand or workbench. If there is any tendency for the stand or workbench to move during operation, the stand or workbench MUST be fastened to the floor. 4. NEVER turn the drill press "on" before clearing the table of all objects (tools, scrap pieces, etc.). 5. NEVER start the drill press with the drill bit or cutting tool in contact with the workpiece. 6. USE ONLY drill bits, cutters, sanding drums and other accessories with 1/2 shank or less. 7. ALWAYS keep hands and fingers away from the drill bit or cutting tool. 8. DO NOT ATTEMPT to drill material that does not have a flat surface, unless a suitable support is used. 9. AVOID awkward hand positions where a sudden slip could cause a hand ...