Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
SPEED CONTROL ADJUSTING SWITCH To increase the operating speed of the drill, turn the variable speed control clockwise. To decrease the speed, turn the variable speed control counterclockwise. REVERSING SWITCH LEVER The reversing switch lever reverses the rotation of the drill bit. It is located just above the trigger switch. ALWAYS turn the motor off and let the bit come to a complete stop before moving the switch. Move the switch to the right for a forward rotation of the bit. Move the switch to the left to put the bit into reverse. Do not change the direction of a moving bit. Make sure the bit comes to a complete standstill before moving switch. Changing direction while the bit is moving can cause damage to the drill. 10 In certain situations, the bit may bind and the drill will kickback in the opposite direction. This sudden reaction could lead to loss of control and possible serious injury. Always be prepared for the possibility of kickback, especially when breaking through material to complete a hole. DRILLING WOOD • Always clamp the work piece to a steady base. Never hold in your hand or across your legs. • Apply pressure in line with the bit. Applying pressure at an angle could cause the bit to bind or break. • Thin materials that may splinter should be drilled with another piece of wood placed underneath. • Twist bits can be used for wood drilling but will overheat if the flutes are not cleared of wood chips periodically. • To prevent splintering when finishing holes, stop drilling just before the hole breaks through and complete the hole from the other side. DRILLING MASONRY • Always use carbide tip bits for drilling masonry. • Use an even pressure, hard enough to keep the drill biting, but not so hard that the bit spins in the hole. Spinning the bit will dull it quickly. Bricks and similar soft materials will take less pressure than a hard material like concrete. DRILLING METAL • Use an even pressure, hard enough to keep the drill biting, but not so hard that the bit spins in the hole. Spinning the bit will dull it quickly. Soft metals like copper, cast iron, brass or aluminum will take less pressure than harder materials like steel. • When drilling harder metals, use lubricating oil on the tip of the bit. MAINTENANCE AND CLEANING Unplug the drill before performing maintenance or cleaning. • Never immerse tool in liquid. Never let any liquid inside tool housing. • Clean with a damp cloth and mild soap. Do not use solvents or harsh detergents. • Check brushes periodically. Worn brushes should be replaced by qualified service personnel. • Keep air vents clean and free from debris. Blocked air vents can lead to overheating. ACCESSORIES Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge number, the heavier the cord (see table below). RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.G AMPERE 10FT. 25FT. 50FT. 100FT. 3-6 18 18 18 18 6-8 18 18 18 16 8-10 18 18 18 14 10-12 16 16 14 14 12-16 14 12 12 - 16-20 12 12 12 - 11 12 date the original purchaser took possession, custody or control of the product, whichever occurred first. This warranty shall be null and void if the product or any component thereof is modified, altered or used for any commercial purpose or on a jobsite. This warranty does not apply to any other product and/or component thereof manufactured or distributed by Alltrade, and does not apply to products and/or components thereof designed, manufactured and/or assembled by others, for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. Warranty Performance By purchasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and/or part is promptly returned to Alltrade’s facility postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723) within the applicable warranty period, with a written request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We recommend that you keep the original product packaging in the event you need to ship the unit. We suggest the package be insured against loss or in transit damage. When sending your product include your name, address, phone number, dated proof of purc...